Company | Booth Number | Signatory PPIM 2025 | Contract date 2025 | Handbook entry approved | Link to Edit Entry |
---|---|---|---|---|---|
Company | Booth Number | Signatory PPIM 2025 | Contract date 2025 | Handbook entry approved | Link to Edit Entry |
Company | Booth Number | Signatory PPIM 2025 | Contract date 2025 | Handbook entry approved | Link to Edit Entry |
---|---|---|---|---|---|
Company | Booth Number | Signatory PPIM 2025 | Contract date 2025 | Handbook entry approved | Link to Edit Entry |
Rhett O’Briant
GUL Americas, Houston, USA
Contact-point corrosion, also known as corrosion under pipe supports (CUPS) presents an ongoing integrity threat and inspection challenge to operators of gas and liquid processing facilities, refineries and compressor stations globally. Contact corrosion most often occurs within difficult-to-access areas such as tightly spaced pipe racks, full encirclement supports, concrete wall or deck penetrations, and air-soil interfaces. The technology now exists for rapid quantitative corrosion measurement within these difficult applications utilizing axially and circumferentially transmitted guided waves.
This novel, low-profile scanning technique is robust and tolerant of pipe surface condition while providing reliable corrosion profile analysis in areas inaccessible by other inspection methods. This presentation will discuss the advantages of guided wave quantitative corrosion measurement and how it can serve to enhance existing inspection programs.
Fan Zhang
Phillips 66, Houston, USA
Due to its body-centered-cubic or BCC crystal structure, carbon steel exhibits a transition behavior of toughness along temperature. The fracture is fully brittle with very low toughness at low temperature, known as lower shelf, and is fully ductile with saturated high toughness at high temperature, known as upper shelf. For the transition region of temperature in between, the steel can exhibit mixed brittle and ductile fracture. This transition behavior is well represented by the transition curve from a Charpy-V-Notch or CVN test.
In quasi static fracture mechanics-based tests, such as J-integral test or crack-tip-opening-displacement or CTOD test, the specimen can exhibit stable crack extension and early unstable crack extension, such as pop-in, if tested at multiple temperatures. In s general transportation pipeline, the surface crack focused by integrity assessment is low constrained and initiates at a static status before failure. Thus, its transition region is at a much lower temperature, more than 100 F for certain cases, than that of a dynamic CVN test or a quasi-static but high constrained standard J-Integral or CTOD test. Thus, A crack feature in a pipe may fail at fully ductile model with burst pressure related to the toughness at upper shelf level even if the tests fall into the transition or even low shelf region at the operating temperature.
In this paper, equations are provided on how to calculate the temperature supporting fully ductile initiation of surface crack in a pipe based on tests data. The worked examples are also provided to demonstrate the application. Certain challenges and potential needs for extra tests are also discussed.
Matt Romney
TD Williamson, Houston, USA
Axial stress corrosion cracking (SCC) has been a known threat for many years. SCC has been found in many pipelines that are susceptible based on material, stress, and environment and are especially prevalent in high pressure gas lines. In-line inspection (ILI) tools such as ultrasonic crack detection (UTCD) and electromagnetic acoustic transducer (EMAT) are designed to detect and size crack anomalies inclusive of SCC. However, in more recent years, circumferential stress corrosion cracking (CSCC) has been found in both gas and liquid pipelines where other stresses (axial, bending, and combined) are present, than those result from pressure alone.
To manage this threat, several operators have adopted magnetic based combination tools that incorporate inertial mapping units (IMUs). These tools enable operators to combine data sets, allowing the assessment of multiple signals. When analyzed together, these signals can help accurately identify and characterize CSCC, as well as rule it out when it is not present. This paper highlights the use of an existing commercially available ILI tool without any modifications to look for CSCC by using multiple data streams such as geometry, metal loss (axial, circumferential and helical), low field magnetic response, internal/external proximity sensors and IMU bending strain.
This paper will present the development of the CSCC model, its application to real pipeline data and some field data feedback.
Monique Roberts1, Leigha Gooding2
1PODS Association, Houston, USA. 2PHMSA, Washington DC, USA
At PPIM 2023 PHMSA and PODS presented on the upcoming NPMS Information Collection Changes with 2024 as “Year Zero” or the baseline foundational year for the new submittal requirements with additional minimum requirements for several years to come.
Now that we are in 2025 we will get an update from Monique Roberts, Executive Director of PODS and Leigha Gooding, PHMSA OPS GIS Manager on what they have learned since their 2023 presentation. Leigha manages NPMS (National Pipeline Mapping System) so we will hear first-hand on the new data attribute requirements for your NPMS submittal for 2025 and beyond as well as lessons learned in Year Zero (2024) from both PHMSA and Operators.
PODS and PHMSA have met with several operators over the last 12 months on their experiences with the new changes so we would like to share that information as well as review the MFA requirements, break out tank info, abandonment items, in-plant submissions and many other items that may need some clarification.
This presentation will also cover a high-level overview of the NPMS submittal process, the radical increase in segmentation and new attributes that PHMSA is expecting operators to capture over the next several years as well as some feedback on the new system from the PODS Community.
Did you know that the NPMS system uses the PODS Model? So, if you have ever uploaded your NPMS submittal you have used PODS! PHMSA has been a member of PODS for over a decade now in fact, so the PODS Association works closely to make sure that all data tables and schema are standardized for use by all operators and service companies that support them. The PODS Model is operator designed to comply with regulations, support specific pipeline operations and decrease risk through digital twin/asset knowledge management.
David Futch1, Sean Moran2
1ADV Integrity, Magnolia, USA. 2Williams, Houston, USA
Circumferential stress corrosion cracking (C-SCC) is being identified on a more frequent basis. More often than not, these indications require repair upon discovery. Repair techniques are limited due to the progression of the crack colonies in the circumferential direction. Industry standards limit the applicability of some repairs as the crack direction lies perpendicular to the applied hoop stress and forms due to an axial or bending stress present on the pipeline. Traditional repair techniques, such as a Type B sleeve, Mechanical Clamp, or grinding may have limitations in some scenarios. Therefore, additional testing of repair techniques is warranted.
C-SCC forms when the pipeline experiences an axial or bending load. In many ways, the environment to form and grow SCC is removed once excavated in repaired or recoated. Therefore, these indications would grow due to normal operations of the pipeline – which may include axial bending cycles. Understanding how the repair technique behaves in a bending regime is critically important to accessing other repair options. This study examines a Type A Compression Sleeve and a Composite Repair for their applicability in repairing C-SCC.
C-SCC colonies removed from service were selected for various repair techniques and one colony selected for an unreinforced control sample. C-SCC indications were strain gaged to monitor growth during the test and samples were installed in a pure bending apparatus. The unreinforced sample was cycled (bending load) to failure and the repaired samples were subsequently cycled to the same amount and then subjected to a burst test. Results show that the use of other repair techniques provide sufficient reinforcement under typical bending loads expected. This allows additional repair techniques when C-SCC is encountered in the field.
Rhett Dotson1, Alex Brown2, Justin Taylor2
1D2 Integrity, Houston, USA. 2TC Energy, Houston, USA
Assessments based on inertial measurement unit technology are an important component of many operator’s geohazard integrity management programs. Bending strain assessments are commonly used by operators to identify areas of the pipeline that have been impacted by geohazards, and strain change assessments can be used to determine the stability of those suspected areas.
Performing a bending strain assessment requires a vendor to successfully identify and classify bending strain features above the reporting threshold as either reportable bending strain features or as manufactured bends. Features identified as manufactured bends are excluded when reporting a bending strain feature or identifying peak strain locations. While the identification of manufactured bends is a critical step in performing a bending strain assessment, there have not been any publications to date examining vendor performance in correctly identifying manufactured bends. This is partly because documentation does not exist for most pipelines conclusively identifying the location of cold bends. However, this does not change the fact that subjectivity exists in bending strain assessments that has not been critically reviewed by the industry.
This paper presents a first of its kind case study examining bending strain assessment performed on a recently built pipeline with records of manufactured cold bends from construction. The paper compares the bends recorded from construction with the bends identified by the vendor. This paper will help operators using bending strain assessments to understand both the subjectivity in these assessments and the expected real-world performance in identifying manufactured bends.
Niels Pörtzgen
ApplusRTD, Rotterdam, Netherlands
As part of the integrity management program, pipelines can be screened for possible damage with efficient in-line inspection (ILI) tools. The type of damage depends on the degradation mechanism such as dents (mechanical damage), wall thickness loss (corrosion) or cracks (fatigue, stress corrosion cracking (SCC)). Although ILI tools have been proven to be adequate for the detection of such damage, accurate characterization and sizing of indications is usually very limited. Therefore, the pipeline can be excavated at suspicious locations identified by ILI tools for confirmation and further investigation with additional non-destructive testing techniques.
For integrity assessment and remaining lifetime analyses, accurate information of the most critical indication or area is required. In case of SCC, the remaining wall thickness between the tip of the largest crack and the surface is most critical. However, SCC often appears as clusters of multiple cracks whereby it is challenging to identify and size the deepest with traditional ultrasonic testing strategies such as the pulse-echo technique, phased array sectorial scanning or the time of flight diffraction (ToFD) technique.
In this paper, we will introduce the latest strategy of ultrasonic inspection based on full matrix capture (FMC) ultrasonic data which is processed in real-time into an image with the IWEX system. With this technique also known as the total focusing method (TFM), it is possible to detect clusters of SCC and to identify and size individual cracks within the cluster.
To demonstrate the performance of the technology, measurements were performed on a test sample. The test sample contained a cluster of SCC in the area of the seam weld of a 10mm thick carbon steel pipe. For reference purposes, the test sample was also inspected with the ToFD technique. Scan results from measurements with IWEX will be presented together with the interpretation. In contrast with traditional technologies, IWEX utilizes multiple ultrasonic travel paths (known as imaging modes) resulting in a comprehensive image which shows the shape of the cracks and its tip which can be used for accurate height sizing. The sizing accuracy will be demonstrated using a reference piece of approximately the same wall thickness containing controlled machined notches at different depths.
The visualization and sizing accuracy are unique for the IWEX system and it facilitates an improved analysis for the pipeline integrity. Furthermore, we will evaluate conditions for adequate use of the technology, and we will discuss practical considerations for use under field conditions.
Pushpendra Tomar1, Geoffrey Krause2, Muthu Chandrasekaran3, John MacLean4
1Dynamic Risk Assessment Systems, Houston, USA. 2Dynamic Risk Assessment Systems, Calgary, Canada. 3NDT Global, Calgary, Canada. 4Inter Pipeline, Calgary, Canada
The aging infrastructure and increasing regulatory requirements have heightened the need for substantial investment in maintaining pipeline system integrity. Consequently, integrity budgets must compete with other financial demands, including growth, expansion, innovation, and strategic acquisitions. It is essential to demonstrate that the integrity investment request is justified and optimized.
This paper presents a financial investment methodology that leverages risk-based likelihood and consequence values, converting them into financial metrics to aid capital allocation and decision-making. This approach evaluates the economic viability of investments by comparing the costs of preventative measures against potential future failure costs in present-day terms. Additionally, it identifies the year when remediation or preventative investments become economically viable.
We illustrate this methodology through a case study for an operator, evaluating whether it is more cost-effective to repair an existing pipeline to support production growth or to construct a new pipeline section at a significant expense. The study involved simulating various operating scenarios and inputs related to revenue, operating costs, maintenance, and repair costs to calculate net cash flow and internal rate of return. By considering the net present value of all investments and benefits, the study determines the economic viability of different scenarios and provides a final recommendation on the repair versus replacement decision.
Richie Joseph1, Saul Chirinos1, Eduardo Munoz2, Pushpendra Tomar2
1Dynamic Risk Assessment Systems, Calgary, Canada. 2Dynamic Risk Assessment Systems, Houston, USA
The viability of a risk model is dependent on the availability and quality of the input parameters. The data gathering effort can either push the risk model (i.e., the model is built around the available data) or be pulled by the risk model (the model dictates the data needs). The former option is not available to US pipeline gas operators that must now adhere to a list of data items prescribed in 45 CFR § 192.917(b). This work produced data quality diagnostic tools, Key Performance Indicators (KPI), and an approach to incorporate data uncertainty into the different types of risk models. A Data Quality Score was developed to allow the internal stakeholders to assess the suitability of the input database before running risk, which is also useful to demonstrate the progress with the data acquisition effort. Data quality KPIs can be evaluated in many dimensions; their development was based on a review of data quality systems for scientific and engineering processes, which had many coincidences with the parameters in the guideline in API Bulletin 1178. The multidimensionality of the data uncertainty makes the definition of the associated meta data a complex task and a possible issue for the database definition. The sensitivity analysis can be leveraged to assess the data importance and minimize the amount of meta data stored. Finally, a guideline for modifying the risk model to compensate for data with high uncertainty. For probabilistic models, the distribution of the input parameter with high uncertainty needs to be modified depending on the nature of source of uncertainty.
The sensitivity analysis can be leveraged to assess the data importance and minimize the amount of meta data stored. Finally, a guideline for modifying the risk model to compensate for data with high uncertainty: For probabilistic models, the distribution of the input parameter with high uncertainty needs to be modified depending on the nature of source of uncertainty.
Tom Bubenik, Matt Ellinger
DNV, Dublin, USA
Pipeline operators use the verification and validation requirements of API Standard 1163, In-Line Inspection Systems Qualifications, to ensure quality in-line inspections (ILIs). Verification confirms an ILI was conducted according to plan, procedures, and processes and that the inspection conditions are consistent with those used to establish the ILI Performance Specification. Validation evaluates the accuracy of the reported anomaly types and characteristics (depth, length, width, etc.) and provides assurance the ILI met its Performance Specification.
Many of the guidelines (i.e., “should” statements) and requirements (i.e., “shall” statements) in API 1163 require the pipeline operator to establish acceptance limits based on pipeline industry experience. Often, API 1163 does not provide guidance on how to establish the acceptance limits. PRCI has developed a guidance document and spreadsheet for conducting the Level 2 and 3 validations and establishing acceptance limits in accordance with the 3rd Edition of API 1163. Both API 1163 and the PRCI documents are widely used in industry to verify and validate metal-loss ILIs, but questions have been raised about the ability to use them for crack-detection inspections. These questions primarily concern the ability to use field non-destructive evaluation (NDE) techniques, which have accuracies similar to or worse than stated ILI Performance Specifications for cracks, to validate the inspections. Simply put, how can an operator validate an inspection when field validation measurements are questionable?
This paper assesses the ability to use API 1163 for crack-detection ILIs including, but not limited to the following:
Several case studies are included to demonstrate the impact of field NDE uncertainties and their impacts on API ١١٦٣ validations.
KEYWORDS: ILI Analysis, ILI Verification and Validation
Shanshan Wu1, Steven Polasik1, Joe Bratton1, Spencer Hoy2
1DNV, Columbus, USA. 2DNV, Calgary, Canada
Operators utilize the calculation methods prescribed in ASME B31.8 Appendix R to predict the likelihood of cracking during the dent formation process. ASME B31.8 Appendix R provides acceptance limits for calculated strain levels below which there is a limited likelihood of crack initiation. Dent strain calculations require detailed caliper measurements, data smoothing, and shape-based analysis for each dent. The industry has been attempting to develop streamlined dent screening criteria based on dent characteristics available in ILI-reported feature listings. These dent characteristics, such as depth, length, and width can be implemented in a screening methodology that does not require the same level of data and assessment as a detailed strain analysis to estimate the likelihood of dent formation cracking.
One such screening criteria that has been used in the industry to assess the sharpness of dents is the length to depth ratio. A length to depth ratio less than 20 has been used by the industry as a predictor of dent sharpness. Logically, a smaller length to depth ratio would indicate a sharper dent and; therefore, a higher strain value. Various studies have compared this ratio to strain estimates with mixed results. This study aims to build on previous studies by incorporating additional data from multiple ILI vendors and tool technologies. Existing screening criteria and industry presented results are explored, along with additional parameters, to identify correlations between dent measurement characteristics and strain results.
If a dent screening methodology based on readily available ILI-reported characteristics is possible, this would result in a valuable tool to enable more efficient assessments, while still maintaining the confidence of a dent strain assessment, to predict the likelihood of cracking during dent formation. This study will share learnings and provide guidelines to be used when considering the development of a dent screening methodology.
Tom Bubenik, Matt Ellinger
DNV, Dublin, USA
API Standard 1163, In-Line Inspection [ILI] Systems Qualifications, was developed to help pipeline operators ensure successful ILI projects. The second edition of the standard is incorporated by reference into the U.S. Code of Federal Regulations Title 49, Parts 192 and 195. The third edition of API 1163 (September 2021) is not yet incorporated by reference but is expected to be soon. In addition, PRCI has developed a guidance document and spreadsheet for conducting verification and validation in accordance with API 1163. Both the second and third editions are widely used in industry to verify and validate metal-loss ILIs.
API 1163 Level 2 and Level 3 validations require an operator to compare field non-destructive evaluation (NDE) measurements to ILI reported dimensions, such as depth, length, and width. Per API 1163, the results of the comparisons are assigned to three “Outcomes” that determine whether the ILI is rejected outright (Outcome 1), further evaluated (Outcome 2), or accepted (Outcome 3).
This paper assesses 100 metal-loss ILIs using the Level 2 requirements of API 1163, 3rd edition, and the PRCI guidance document/spreadsheet. The case studies involve actual ILIs that were previously performed by pipeline operators to ensure the integrity of their pipeline systems. The results indicate that API 1163 is more stringent than expected.
This paper demonstrates that:
The PRCI guidance document and spreadsheet also provide an “equivalent” tolerance for Outcome 2 cases, and they give a method to estimate of the actual ILI performance using a Level 3 approach for Outcomes 2 and 3. Lessons learned from these evaluations are discussed and guidelines for use are given.
Finally, the paper identifies several errors in the PRCI spreadsheet. The authors understand PRCI is addressing and correcting these errors, which affect the calculated probability of detection (POD), probability of correct identification (POI), false call rate, and false negative rate.
Matt Ellinger1, Andy (Hao) Li2, Stacy Hickey1, Adriana Nenciu1, Pam Moreno3, Ben Ross1, Shanshan Wu1
1DNV, Dublin, USA. 2Plains Midstream Canada, Calgary, Canada. 3DNV, Houston, USA
In-line inspection (ILI) run-to-run comparisons can provide valuable insights into the integrity of a pipeline asset. Results from an ILI run-to-run comparison can be utilized to identify anomalies that might become critical prior to the next planned integrity assessment. Alternatively, or in addition to, ILI run-to-run comparison results may indicate that an anomaly that is part of existing excavation plans may not be predicted to reach criticality prior to the next planned integrity assessment. In these cases, such anomalies are perhaps removed from existing excavation plans and replaced with anomalies that are more likely to reach criticality. This allows for more efficient and effective use of limited resources while decreasing overall risk.
Often, corrosion growth rates are established by comparing ILI spreadsheet listings between subsequent inspections. Examples of how to derive spreadsheet-based corrosion growth rates include, but are not limited to:
Relying only on ILI spreadsheet listings to derive corrosion growth rates may result in a misrepresentation of the actual corrosion growth (or lack of growth) that may be occurring in a pipeline segment. By incorporating ILI signal review comparisons between the subsequent surveys, definitive evidence of corrosion growth (or lack of growth) can be established, and more realistic corrosion growth rates can be derived.
In this case study, the authors applied the spreadsheet-based corrosion growth rates (described above) to identify anomalies calculated to reach criticality prior to the next planned integrity assessment. The authors then performed ILI signal review comparisons at this subset of anomalies to establish more realistic corrosion growth rates. Upon applying the signal review-based corrosion growth rates, the number of anomalies calculated to reach criticality prior to the next planned ILI survey was reduced.
Additionally, several anomalies which spreadsheet comparisons indicated were growing minimally were found to be growing at higher than spreadsheet calculated rates. This resulted in the addition of some anomalies to the excavation plan that were previously considered lower criticality.
The reduction in anomalies calculated to reach criticality and the addition of a few anomalies previously considered non-critical prior to the next planned ILI survey will be utilized by the pipeline operator to optimize their excavation program. The result is less overall repair cost coupled with a reduction in risk.
KEYWORDS: ILI analysis, ILI run comparison, Corrosion growth assessment, ILI signal data
Cassidy Ryan1, David Classen1, Steve Farnie2, Oleg Shabarchin3
1Baker Hughes, Houston, USA. 2Baker Hughes, Cramlington, UK. 3Enbridge, Houston, USA
A hard spot is defined in the 2024 PRCI hard spot susceptibility review as “localized area in the body of the pipe having elevated hardness levels compared with normal hardness levels prevalent in the rest of the pipe body. They are, in most cases, the result of unintended rapid cooling (quenching) of the steel while in a hot condition in the plate or hot strip mill, or during the forming or forging process for seamless pipe or fittings, with or without benefit of subsequent annealing or tempering.” When stressed, they can be subject to failure from mechanisms such as hydrogen-stress cracking or fracture cracking. Industry experience in managing the hard spot threat paired with the recently published operator susceptibility review have raised awareness to the importance of a reliable inline inspection (ILI) hard spot specification to detect and classify hard spots. Validation data is key for developing a robust specification.
This paper describes how, in collaboration with industry partners, an enhanced solution for hard spot detection and reporting with a robust POD, POI, and POS specification has been demonstrated. Using a three-pronged approach, applied to an established hard spot ILI technology, a rigorous re-validation was conducted comprising testing of essential variables in three design environments. Extensive pull tests, existing and historical dig data, and FEA modeling in the comprehensive development program utilized multiple data streams to establish an enhanced specification and refine classification techniques to ensure confident hard spot identification – and, therefore, efficient dig programs. The enhanced hard spot assessment process was applied to historical inline inspection data to add further optimization and confidence in the derived specification.
Furthermore, the paper will describe how the program not only considered all essential variables in the process and certified an analysis process for the classification of the various hard spot feature types but then how it was effectively extended to three MFL platforms. The result – a broad range of opportunities for combination inspection with standard, planned corrosion inspections.
Inessa Yablonskikh1, David Buttle2, Steve Worthington3, Cassidy Ryan4
1Baker Hughes, Cramlington, UK. 2Baker Hughes, Oklahoma City, USA. 3Baker Hughes, Calgary, Canada. 4Baker Hughes, Houston, USA
Over 15 years ago, pipeline operators requested the development of an in-line inspection (ILI) axial strain measurement tool to support their geohazard management programs. Since then, Axial Strain Measurement Inspection Service (AXISSTM) has been employed on over 25,000kms of pipeline with many high strain locations successfully identified and mitigated. Like any new technology, it took the axial strain tool a few years to become a unique, established and proven tool for a pipeline operator to assess geohazards, movement and other strain – related threats.
Over the years, the operators’ experience has provided key insights as to where the current technology strengths lie and of course where the provision of additional information could further enhance their integrity engineers’ more complete understanding of stress and strain-based threats to then develop proactive mitigation strategies and importantly conduct more cost-effective repair programs – ensuring their pipeline’s safe and continuing operation.
This paper presents a response to these learned and clearly defined needs. It introduces a new bi-axial stress measurement inspection technology, AXISS™ EPS, that adopts these required advancements by providing detailed information on the entire stress landscape of both active loading and residual stresses. The proprietary sensing technology used by this new tool is an evolution of a mature stress measurement technique that has successfully delivered bi-axial stress measurements for steel structures for the last 3 decades in a range of industries including flexible pipeline riser systems in the offshore oil and gas industry as well as nuclear, automotive, aerospace and rail.
This paper provides a comprehensive overview of the new bi-axial stress tool technology, and a summary of the testing validation and verification program. By focusing on the proven performance, the paper will demonstrate the advancements introduced to the AXISS EPS system versus the previous AXISS system, that provide operators an understanding of their pipelines’ total stress and strain status in both the elastic and plastic regions, which in the past would rely on key assumptions to conduct assessments. Using measured condition data will lead to optimized fit-for-service decision-making. In addition, there will be a discussion on how these new advancements will enhance the integrity engineering assessment for high-risk zones such as bends and girth welds.
Benjamin Mittelstadt1, Terry DeLong2, Matthew Nicholson3, Brian Jimenez4, Robert Zmud5
1Dynamic Risk Assessment Systems, Houston, USA. 2Enbridge, Calgary, Canada. 3TC Energy, Houston, USA. 4Energy Transfer, Houston, USA. 5Dynamic Risk Assessment Systems, Calgary, Canada
The deployment of In-Line Inspection (ILI) tools plays a critical role in pipeline integrity management helping ensure reliability and safety of a pipeline system. ILI tools employ various technologies to gather data used to detect and characterize anomalies including but not limited to metal loss, cracks, or deformations in the pipe wall.
Determining and appropriately considering ILI tool measurement tolerances is critical in the interpretation of the data collected. ‘Determining’ is how the tool tolerance is estimated and quantified, whereas ‘considering’ is the process decision on how use tool tolerance is used in a program. Measurement tolerance (or tool tolerance), in this context, denotes the range of error or deviation between the true value and the measured value reported by the ILI tool. ILI vendors define specific tolerances for each measurement parameter accounting for the tool’s design, calibration, and intended application.
Various methods exist for considering measurement tolerance, varying from the deterministic addition of pre-determined values based on prior tool performance and desired safety targets to reliability methods using statistical techniques that consider the sources of uncertainty individually. Each method has certain practical advantages and challenges that must be understood.
Justin Bekker1, Sri Chimbli2
1Stress Engineering Services Canada, Calgary, Canada. 2Stress Engineering Services, Houston, USA
The in-service welding of pipelines, i.e., sleeves and hot taps, presents unique challenges from accelerated cooling, residual stresses, and risk of burnthrough. While adherence to relevant welding codes is essential, it may not be sufficient to ensure the weld integrity. This paper explores factors beyond code requirements that must be considered when qualifying welding procedures for in-service applications with fillet, groove and overlay welds. The standards that are followed in North America are API 1104, CSA Z662, and ASME B31.3 (which references ASME BPVC Section IX). The essential variables of these codes are generally similar to ASME BPVC Section IX, with some additional requirements, such as closer attention to heat inputs, cooling rates, and the resulting hardness.
Standards require that the cooling rate and welding restraint be considered, but do not state specific requirements. Hardness requirements are specified but the hardness test locations are open to interpretation and standard CSA Z662 allows higher hardness values at an engineer’s discretion. Further, determining acceptable heat inputs for minimizing the risk of burnthrough in a thin-wall pipe is not specified. These aspects of the codes requiring consideration and determining acceptable heat inputs is critical to ensure safety of the welding crew and long-term integrity of the in-service welds. This paper provides the industry best practices on these considerations.
KEYWORDS: Welding, in-service, hot tap, sleeve
Eric Jenkins1, Stella Cunha2
1Tetra Tech, Denver, USA. 2Enbridge, Calgary, Canada
The challenge in many erosion remediation projects for pipeline water crossings lies in achieving a delicate balance: providing robust, protective coverage for the pipeline while minimizing impacts on aquatic life and the natural progression of the waterbody. Often, these projects resort to pipe lowering, a costly and environmentally disruptive measure that can interrupt pipeline operations, leading to service disruptions and financial losses. Although such projects ultimately yield a pipeline with reduced integrity risk alongside a naturally developing water body, the high costs involved often divert funds away from addressing other integrity issues. This can lead to further degradation of low cover and exposed sites awaiting funding.
The Enbridge L41 pipeline at the South Fork Nemaha crossing, which suffered from low cover due to both downward and lateral scour, serves as a case study. This study will detail five methodologies implemented to ensure adequate pipeline protection while facilitating the passage of aquatic life under typical low-flow river conditions. Initially, the project team pinpointed two upstream structures that altered historical flow patterns as the primary causes of increased scour, addressing these root causes as feasibly as possible. Secondly, a concrete mat system was deployed over the pipeline to provide cover without significantly elevating the riverbed. Thirdly, the bank, previously near-vertical and prone to scour and slough, was regraded to a more stable 2:1 slope to mitigate flooding during heavy rain. Fourth, traditional riprap was used to armor the bank’s toe up to the ordinary high-water mark, safeguarding against typical annual high flow events. Lastly, the area above the high-water mark was revegetated using willow species indigenous to the region, known for their rapid propagation and strong rooting on riverbanks, offering natural erosion protection during extreme flooding.
Daniel Sandana, Lauren Guest, Emily Burrow
ROSEN, Newcastle upon Tyne, UK
Carbon Capture and Storage (CCS) involves the conveyance of carbon dioxide (CO2) through pipelines from the capture facility to a storage field. While CO2 can be transported in a gaseous state, the dense or supercritical state is preferred due to efficiency and project economics, particularly for storage applications. This paper will review the integrity threats faced by purpose built and repurposed CO2 pipelines and the role of in-line inspections (ILI) in detecting and sizing critical defects while overcoming the mechanical and operational challenges of this medium.
The management of time-dependent threats in CO2 pipelines must overcome unique challenges in these high-pressure dense phase operations, which can be compounded with the presence of impurities originating from various industrial processes and applications. This paper reviews, in line with current industry understanding, the time-dependent threats which could arise in pure (naturally occurring) CO2 and anthropogenic (man-made) CO2 pipelines depending on operational scenarios. Key gaps and challenges are highlighted.
The requirements of in-line inspection programs in CO2 pipelines, aligned with the integrity threat review, are discussed, including specific considerations for pipeline change of product (repurposing). Considering historical pipeline design and practices (e.g. diameter, thickness, toughness), high operational stresses and specific offshore axial load considerations for offshore applications, the paper reviews critical flaw dimensions e.g. volumetric, crack-like, that may be applicable and reviews the capability of ILI under these circumstances.
The paper then reviews the key design, mechanical and operational considerations and challenges associated with CO2 pipelines, considering fluid-specific properties, in successfully ‘designing’ and deploying in-line inspection programs in dense CO2. For example, the operational parameters and pipeline construction have key roles in defining the most adequate combination of in-line technologies and also the actual configuration of each cleaning pig and inspection tool. The current industry ILI limitations of diameter and pipeline wall thickness are also highlighted; this is of particular importance considering a trend of CO2 pipeline designs asking for higher wall thicknesses to address fracture propagation and accelerated corrosion issues, to the detriment of inspection capabilities (and thus safe integrity management) .
Exposure testing of tool components, customization of tool configurations, and proving robustness both mechanically and in terms of technology repeatability through a track record all contribute to in-line inspection run success in this increasingly important medium.
KEYWORDS: CO2, CCUS, ILI, pipeline integrity, repurposing, testing
Yougui Zheng1, Pedro Rincon1, Adam Maggio2, Ryan Meyer2, Eric Pierce2
1Shell Global Solution US Inc., Houston, USA. 2Shell Exploration & Production Company, New Orleans, USA
This study provides a comparative analysis of Internal Corrosion Direct Assessment (ICDA) and In-Line Inspection (ILI) methodologies for subsea pipelines. It reveals that while ICDA is effective in predicting corrosion depth during its Pre-assessment and Indirect Inspection stages, it struggles with accurately locating specific damage points. This difficulty arises because internal corrosion is often localized and influenced by factors like severe corrosion at joints, making it challenging to identify critical defects even when predictive models highlight vulnerable areas. Moreover, there is a notable difference in the effectiveness of inspection and defect detection when conducted onshore compared to offshore environments.
The study also explores the impact of corrosion inhibitors on inspection processes. These inhibitors are generally effective against widespread corrosion but are less effective at preventing localized pitting. This variability introduces randomness on predicting defect location, which challenges the standard inspection approach outlined by NACE SP-0116. This standard assumes a pattern of widespread corrosion for detailed examinations, but it is inadequate for pipelines with inhibitors where pitting is unpredictable.
To address these issues, the study recommends enhanced inspection strategies. For pipelines that cannot be inspected using traditional pigging methods, it suggests increasing inspection frequency beyond the ICDA guidelines. These adjustments aim to improve defect detection accuracy and better manage the complexities introduced by corrosion inhibitors, ultimately ensuring more reliable pipeline integrity.
KEYWORDS: Direct assessment, ILI analysis, Corrosion Prediction, Inhibitor, Localized Corrosion
Lewis Barton
ROSEN UK, Newcastle, UK
In-Line Inspection (ILI) is widely used to monitor pipeline conditions, identify and size defects, and meet regulatory requirements. However, alternative approaches for ‘non-piggable’ pipelines are needed where ILI is not feasible. In these cases, knowledge-based models relying on data, engineering assessments, and assumptions are required.
External Corrosion Direct Assessment (ECDA) is a process where variables believed to contribute to corrosion are combined with above-ground surveys or computational modeling to identify corrosion ‘hotspots’ for in-field investigation. However, these techniques have several known limitations, leading often to wasted excavations and lingering uncertainty
To enhance the direct assessment process, ROSEN has incorporated predictive analytics from its Integrity Data Warehouse (IDW). The IDW contains data from over 26,000 in-line inspections, covering more than 620,000 miles (1,000,000 kilometers) globally. These data provide significant improvement in predictive capacity and the likely condition of pipeline assets across all diameters, pressures, and fluids.
ROSEN has also begun incorporating Large Stand-off Magnetometry (LSM) into its direct assessment approaches. LSM detects changes in the magnetic signature of the pipeline that correlate with increased stresses, enabling the detection of a wide range of stress-raising anomalies and defects. This adds another layer of information, allowing for the greater confidence in the identification of potential excavation sites.
This paper provides a detailed overview of the new process and the improvements made through the addition of LSM and the integration of the IDW.
Rafael Wagner Florencio dos Santos1, Thomas Gabriel Rosauro Clarke2, Henrique Tormen Haan de Oliveira2, Alberto Bisognin2
1Petrobras, Rio de Janeiro, Brazil. 2UFRGS, Porto Alegre, Brazil
This paper presents the development and field testing of an innovative submersible guided wave monitoring system designed for the integrity assessment of subsea pipelines. The research addresses the critical need for non-intrusive, long-range inspection techniques in offshore environments.
The study focused on creating a robust electromagnetic acoustic transducer (EMAT) collar capable of operating in submerged conditions and through pipeline coatings. Through iterative design and testing, we developed a sensor configuration that optimizes signal generation and reception while maintaining functionality under high-pressure environments.
Key aspects of the research included:
The field trials validated the system’s capability for underwater installation and operation, with divers reporting ease of handling and rapid deployment. The collar’s design allowed for both wet-mate and dry-mate electrical connections, offering flexibility in installation methods.
Results from the field tests showed that the developed system could effectively distinguish defects and the performance indicates the potential for early detection of pipeline integrity issues in subsea environments.
This research represents a significant advancement in subsea pipeline monitoring technology, offering operators a non-intrusive, long-range inspection tool capable of continuous integrity assessment. The system’s ability to function through coatings and in submerged conditions addresses key challenges in offshore pipeline maintenance.
This paper provides valuable insights into the development and real-world application of guided wave technology for subsea pipeline integrity management, demonstrating its potential to enhance safety and efficiency in offshore operations.
Brett Davis1, Brian Patrick2, Liyu Wang1, Heather Watson1, Ted Zirkle3, Alexander Hudgins1, Yash Bhargava1
1Exponent, Menlo Park, USA. 2Pacific Gas & Electric, San Ramon, USA. 3Exponent, Philadelphia, USA
This work is motivated by the regulations in 49 CFR § 192.712(e)(2)(i)(E) that allow for use of “other appropriate values” to provide conservative Charpy V-notch (CVN) toughness estimates for crack-related conditions of pipeline segments in the absence of direct laboratory test data for the subject segment. This work extends previous efforts by investigating pipe features and characteristics (e.g., installation date, and seam type) that can inform the statistical determination of conservative CVN estimates for a given data set. Database sampling, documented trends in manufacturing and mechanical properties, and statistical analysis are leveraged to examine the significance of factors related to CVN measures. Results show that pipe vintage and seam type are two factors with correlation to CVN, which can be used for clustering and statistically evaluating a large material testing database. Furthermore, clustering analyses of a material testing database are used to evaluate the relationship of various pipe characteristics including vintage, seam type, pipe geometry, and chemical composition to CVN toughness of gas transmission line assets.
KEYWORD(S): Fatigue, strain, strength, toughness studies and management; Materials identification, verification; Charpy V-notch (CVN); Fracture mechanics; Engineering critical assessment
Benjamin Nowell, Thomas Dessein, Daryl Bandstra
Integral Engineering, Edmonton, Canada
Many North American operators are currently evaluating options to blend hydrogen into their natural gas systems. The introduction of hydrogen may impact the long-term structural integrity of steel pipelines, with particular influence on crack-like anomalies due to embrittlement of the steel and increased fatigue crack growth rates. Crack-like anomalies such as those found in seam welds should be assessed for hydrogen-blended service with a crack assessment model capable of handling low toughness failures such as API 579 or the PRCI MAT-8 model, with proper adjustments to account for the effects of hydrogen.
This paper illustrates the limitations of conventional fatigue assessment methods when assessing integrity and risk of crack-like anomalies in blended hydrogen service and provides a technical review of factors influencing the assessment. This includes a summary of suitable assumptions regarding the variability in pipe strength and vintage seam weld toughness properties, the expected density, depths, and lengths of the population of defects expected on uninspected pipelines, and a comprehensive review of historical mill test pressure requirements. A range of example analysis cases are presented to demonstrate the impact of embrittlement and accelerated fatigue crack growth rates due to hydrogen, and how this is affected by the operating conditions of the pipeline, such as the pressure loading history, current stress levels, and historical mill pressure tests.
h3 class=”paperno”>259
Rafael Wagner Florencio dos Santos1, Miguel de Andrade Freitas2, Lucas Braga Campos3, Guttemberg Coelho Da Silva2, Cesar Giron Camerini3
1Petrobras, Rio de Janeiro, Brazil. 2PUC-Rio, Rio de Janeiro, Brazil. 3UFRJ, Rio de Janeiro, Brazil
This paper describes the development of an instrumented pig that accommodates the diameter variations expected in sections of cladded rigid pipelines to ensure the detection of cracks in the cladded layer at the weld region of these pipelines, before the crack penetrates through and the carbon steel is exposed to the highly corrosive fluid. This development was motivated by the absence of a similar solution in the market to meet the demand. The benefits to be gained from using this pig include the optimization of operational availability through the mitigation of early failures or the extension of pipeline service life, and the reduction of inspection costs in the event of failure and the need for comprehensive assessment, as no vessels will be required.
The general methodology applied to this project can be described in four steps:
1. Development of a bench simulation of the pipeline, with cladded materials and liners containing artificial defects. Various activities were initiated from this bench, such as: mechanical design, electronic design, software development, execution of more complex tests, and simulation and processing of eddy current signals;
2. Prototype manufacturing, including fabrication, assembly, and laboratory testing;
3. Execution of full-scale tests, where field conditions are simulated, allowing the prototypes to be developed as close to reality as possible; and
4. Execution of real field inspections, with the issuance of reports and technical certificates.
This paper will present the results obtained throughout the project.
Jason Edwards1, Simon Slater1, Ann Reo2, Sean Moran3
1ROSEN, houston, USA. 2Williams, Tulsa, USA. 3williams, Salt Lake City, USA
Managing the threat of hard spots has been on the agenda of pipeline operators for several years. It is fair to say that the industry understanding of what hard spots are, how they are formed and how we can manage them has advanced rapidly but is still evolving. The industry knowledge has been recognized by PHMSA and an advisory bulletin was issued discussing the threat of hard spots. Industry now has a good feel for the susceptibility of different pipe types and vintages, and there is good appreciation that not all hard spots are the same and variations in morphology result in different types of hard spots and different ILI signal patterns. The current status is predicated on the significant amount of validation work that operators are performing in response to ILI. However, the industry is not standing still, and since the last PPIM conference more information has become available that has led to further improvements. This presentation discusses the recent experience, bringing together the latest results from ILI, non-destructive testing and research activities to continually advance assessment methods for managing the threat of hard spots.
Pablo Cazenave, Katina Jimenez, Ravi Krishnamurthy
Blade Energy Partners, Houston, USA
In March 2019, the U.S. Pipeline and Hazardous Materials Safety Administration (PHMSA) issued a Research Announcement to improve the detection and sizing accuracy of In-Line Inspection (ILI) systems for critical pipeline anomalies, aiming to improve safety and reduce unnecessary excavations. In response, Pipeline Research Council International (PRCI) launched Project NDE-4-19 in December 2019, a multi-phase initiative in collaboration with PHMSA and Blade Energy.
The project brought together Pipeline Operators, ILI Technology Providers (TPs), and Subject Matter Experts to assess and improve ILI system capabilities for challenging corrosion features. A data-driven approach was used, in which recent Root-Cause-Analysis (RCA) reports of corrosion-related pipeline failures were analyzed and a pipe test string was designed with complex corrosion profiles resembling those associated with the failures. The manufactured corrosion features were documented using advanced non-destructive evaluation (NDE) techniques.
Three ILI TPs tested their tools on the designed pipe test string in a series of blind pull-through tests. Following initial evaluations, the TPs received feedback on detection and sizing gaps and were provided with detailed 3D corrosion profiles to guide their improvements. A second round of tests measured the enhancements in detection and sizing accuracy, identifying improvements and remaining challenges.
This paper presents the findings from this 3.5-year long project, highlighting advancements in ILI technology and ongoing gaps in detecting and sizing problematic corrosion profiles.
KEYWORDS: Pipeline Integrity, ILI Validation, ILI Improvement, ILI detection capability, ILI sizing accuracy, corrosion integrity evaluation.
William Deschamps-Robertson1, Keegan Diebold2, McKenzie Kissel1
1Onstream Pipeline Inspection, Calgary, Canada. 2Cenovus Energy, Calgary, Canada
The gathering market primarily involves small-diameter pipelines, typically ranging from NPS 3 to NPS 6, with NPS 3 and NPS 4 being the most common sizes. Construction practices for these pipelines emphasize rapid installation to align with the operational timelines of wellheads or production pads, making inspection and maintenance secondary considerations. These pipelines often feature tight bends, heavy wall thicknesses, and variable product flows and pressure conditions that are not ideal for inline inspection (ILI), especially for smaller diameters like NPS 4.
Historically, inspecting these pipelines required taking them offline and accessing them through bell holes or mid-bend risers, using tethered wireline or crawler systems. However, recent economic shifts have led to higher operating pressures and increased throughput, necessitating a more efficient inspection approach with minimal operational disruption.
This paper reviews the common challenges faced by Cenovus Energy with their gathering systems and highlights the iterative design and development process undertaken by Onstream to advance a NPS 4 1.5D TriStream MFL™ technology. This combination MFL, caliper and inertial mapping tool is designed to inspect gathering lines that were previously deemed uninspectable due to their tight bends and heavy wall thicknesses. The paper will also present a case study of a recent 1.5D inspection conducted for Cenovus Energy. This inspection, which had previously been performed using a tethered wireline tool five years ago, was recently achieved with a free-swim ILI tool, demonstrating the technological advancements and improved inspection capabilities.
Gerardo Chavez1, Johannes Spille1, Keila Caridad2, Alvaro Vega2, Neil Shortt3, Aaron Schartner3
1ROSEN, Houston, USA. 2TCE, CDMX, Mexico. 3TCE, Calgary, Canada
Offshore pipelines pose unique challenges to their integrity management, particularly when standard in-line inspection tools cannot accommodate their complex conditions, such as heavy pipe walls, high pressures and high medium flows. The Sur de Texas-Tuxpan (SdTT) pipeline is a 42-inch natural gas system with two offshore segments spanning 310 miles (498 km) and 156 miles (251 km), wall thicknesses up to 1.8 inches (45 mm), pressures up to 1,700 psi and flows up to 10 mph that required innovative solutions beyond conventional inline inspection tool designs to perform a successful inspection.
To meet these challenges, ROSEN developed a custom ILI tool that combined Axial Magnetic Flux Leakage technology with Internal Eddy Current technology (IEC) in a single tool configuration. This tool was optimized for thick-walled pipelines, capable of detecting and sizing internal and external anomalies under high-pressure and high-flow conditions. A key enhancement was the Speed Control Unit (SCU) to maintain a consistent (slow) tool velocity ensuring optimum data quality.
Extensive simulations and validation tests have been performed to optimize magnet strength, brush configuration and speed controlling capabilities to tackle the three main challenges: heavy pipe wall, high pressure and high flow.
This paper presents the technical solutions and lessons learned from the SdTT project, highlighting the challenges and efforts to ultimately achieve a successful inline inspection. The advancements in ILI tool design provide valuable insights into managing the integrity of heavy wall offshore pipelines.
Brian Ellis1, Nigel Curson2, Louise O’Sullivan2, Blake Bixler3, Rabindra Chakraborty4
1pipelinelogic, Lakewood, USA. 2Penspen, London, UK. 3Senslytics, Oklahoma City, USA. 4Senslytics, Atlanta, USA
The Gas Mega Rule imposes stringent requirements on pipeline operators, particularly in high-consequence areas (HCAs), but it also provides an opportunity to digitize integrity management practices. By integrating digital twins, AI-driven compliance solutions, and multiple inline inspection (ILI) runs, operators can move beyond regulatory compliance while enhancing pipeline safety and operational efficiency.
Digital twins act as virtual models of pipeline systems. These models enable predictive analytics, allowing operators to simulate risk conditions like corrosion and stress, and prioritize maintenance and inspections where needed. This proactive approach reduces unnecessary work and targets integrity management funds to high-risk areas, maximizing safety while minimizing costs.
Multiple ILI runs, using technologies like magnetic flux leakage and ultrasonic testing, generate vast datasets that can be consolidated to provide a clear view of pipeline conditions. This streamlines decision-making, reduces downtime, and optimizes repairs, extending pipeline life and cutting maintenance costs. With AI integration, operators can automate data processing, anomaly detection, and regulatory reporting, meeting Mega Rule compliance while improving efficiency. AI also helps predict corrosion growth, optimize inspection intervals and chemical programs, improve integrity assessments even when not all data is available, and reduce human error, allowing engineers to focus on high-value tasks.
By integrating AI compliance tools with digital twins and ILI data, operators can turn compliance into a strategic advantage. AI-driven insights enable faster, more accurate decision-making and preemptive maintenance actions, improving safety and reducing operational costs.
KEYWORDS: Gas Mega Rule, digital twins, Artificial Intelligence (AI), Inline inspection (ILI), predictive maintenance, anomaly detection
NOTE: This is a continuation of previous work published by the authors. Real life examples of aligning up to 7 consecutive ILI runs over 14 years will be discussed, along with the influence of AI over the lifecycle of concurrent runs and overall mega rule compliance. This will be added to the as the content develops.
Atul Ganpatye1, Emmanuel Valencia1, Debartha Bag2
1ADV Integrity, Inc., Magnolia, USA. 2Enbridge, Houston, USA
Hard spots in pipelines have been historically associated with multiple failures. Although assessment of hard spots is a critical aspect of integrity management of pipelines, several aspects of the detection, identification, measurements, and evaluation of hard spots have posed continuing challenges for the industry. One of the fundamental issues that forms the bedrock of integrity management approach for hard spots is the uncertainty in the measurement and interpretation of the hardness values associated with hard spots. Indeed, what cannot be reasonably measured cannot be effectively managed. The aim of the paper is to discuss interpretation of hardness data in light of measurement techniques, tools, procedures, statistical variation, and characteristics of hard spots. The paper will highlight multiple perspectives that will provide a more complete understanding of hardness measurements towards comprehensive integrity management of hard spots.
The paper will focus on a case study that will include the findings from the examination of a set of recently excavated hard spot features in 30 inch A.O. Smith pipe. Specific results from in-the-ditch NDE activities, and detailed laboratory-based examinations will be presented and interpreted. Results will be discussed in light of potential improvements for increasing confidence in the in-the-ditch hard spot evaluation techniques. The findings and recommendations discussed in the paper will be practical and can be readily implemented by operators and NDE vendors for better management of hard spots going forward.
Rhett Dotson1, Liam Hagel2, Jing Wang2, Rick Wang2, Duncan Wang1
1D2 Integrity, Houston, USA. 2TC Energy, Calgary, Canada
Curvature-based strain assessments have served as the basis for identifying injurious dents in natural gas pipelines for the last decade. Improvements have been made to the original ASME B31.8 equations over the last six years, and a decade of studies have resulted in broader application of the strain limit damage (SLD) and ductile failure damage indicator (DFDI) as suitable methods for assessing strain limits. While these methods have been shown to be capable of identifying dents that have formation cracking, there are examples where cracking has been found in dents with low strains. This paper examines three separate case studies of dents with acceptable strains where cracking was found during excavations. Initial curvature-based strain calculations and finite element-based strain calculations presented in prior publications did not accurately identify these dents as having critical strains or being susceptible to formation-induced cracking. This study examines other factors that may have led to the observed cracking including changes in restraint condition, variations in maximum internal pressure, or tool tolerances. The paper concludes with considerations for identifying these features in future assessments and provides recommendations to operators using curvature-based strain assessments.
Atul Ganpatye1, Ahmed Hassanin1, Matt Jaouhari2
1ADV Integrity, Inc., Magnolia, USA. 2Bechtel Energy, Houston, USA
This paper provides a parametric overview of the design parameters that influence the installation and performance of Type A compression sleeves on pipelines. When designed and installed correctly, Type A compression sleeves can be effective in reducing the net hoop stress in the carrier pipe. At the functional level, the interaction between a compression sleeve and the carrier pipe manifests as an interference fit where the installation is achieved by way of thermal expansion of the sleeve rather than by the use of mechanical force (without the interference fit aspect, the functionality degrades to a traditional Type A sleeve).
On account of the nature of the initial stresses imparted on the sleeve (tensile) and the carrier pipe (compressive) during installation, some level of optimization of installation parameters is necessary to achieve the desired final stress levels in the carrier pipe as well as the sleeves. This requires careful consideration of the temperature difference between the carrier pipe and the sleeve, material properties of both the pipe and the sleeve, sleeve thickness, and operation and hydrostatic testing pressures. By way of examples, the paper demonstrates the influence of such parameters on the performance of compression sleeves and the resulting state of stress in the carrier pipes. The paper will also address the effect of installation pressure on the performance of the sleeves.
The paper follows an analytical approach that utilizes spreadsheet-based mathematical modeling of the system parameters as well as finite element analysis (FEA). FEA results also provide additional insight into the circumferential and axial distribution of stresses along the sleeve as well as the carrier pipe. A more rigorous understanding of the performance of the compression sleeves will allow wider application opportunities for such sleeves and allow better control of the performance.
Rhett Dotson1, Liam Hagel2, Jing Wang2, Rob Greene1
1D2 Integrity, Houston, USA. 2TC Energy, Calgary, Canada
Over the past decade operators have used curvature-based strain assessments to assess the likelihood of cracking associated with dent formation in natural gas pipelines. Accurate curvature-based dent strain assessments require that the dent shape is captured with a high-resolution caliper tool, where high-resolution is defined by the number of sensors around the circumference of the pipe. However, the use of a high-resolution caliper tool can be infeasible due to restrictions such as multi-diameter passages, internal obstructions or small diameter. This paper presents a case study where multiple inspections were performed in an 8-inch line using low-resolution caliper tools. The initial conservative estimates of the dent strain identified a significant number of dents with exceptionally high strains. A multi-step process was developed to improve the dent strain assessment. First, methodologies to estimate upper and lower bound strains based on a single data set are presented. Next, a methodology is developed and presented to combine the low-resolution data sets from multiple inspections. Finally, the paper compares these results from the first two steps with the results of optical scans performed on excavated dents and the results of numerical analysis. This paper will be helpful for operators who have inspection scenarios that are limited to low-resolution caliper tools or may not have high-resolution data available.
Xuejun Huang, Bryan Feigel, Aidan Ryan, Intisar Rizwan I Haque, Ryan Lacy, Simon Bellemare
Massachusetts Materials Technologies, Natick, USA
The toughness of pipeline materials, particularly in fracture toughness, is important for assessing the fitness-for-service of pipelines. With the advent of ultra-high resolution inline inspection (ILI) tools, the demand for fracture toughness data has risen. Current approaches to obtain fracture toughness include performing cutouts and destructive testing, leveraging existing databases, and nondestructive evaluation (NDE). A previous PPIM paper demonstrated an innovative NDE method called planing-induced microfracture and validated the method for estimating fracture toughness using a lab prototype. Based on this successful validation, a portable field tool, Blade Toughness Meter (BTM), has been developed. Compared to the lab prototype which cuts and splits small specimens at the center, the field instrument can be directly attached to a pipe to perform surface preparation and testing. The instrument first creates raised testing surfaces by machining called “islands” on the pipe surface and then planes these islands with specially designed blades with a central opening. A true microcrack is introduced at the surface of the pipe and ligaments left on the chip and substrate are scanned. An in-depth characterization of the ligament profiles reveals features that exhibit varying degrees of correlation to fracture toughness. The fracture surface was also examined using a scanning electron microscope (SEM), which allows for a qualitative assessment of whether the material is ductile or brittle. Fracture toughness prediction models have been built using the outcome of BTM testing together with other material properties, showing accuracies of approximately ±20% comparing to lab-tested values. This paper will summarize the fundamental basis for the test, present details on the material response including fractographic evaluation and characterization of the fractured ligaments, and provide validation results. These findings may be used to evaluate the technology readiness for initial implementation as part of integrity programs.
David Cockfield
Pipeline Innovations Ltd, Cramllington, UK
Pathfinder is a soft foam bodied pipeline caliper tool capable of passing through a 40% reduction in the nominal pipeline bore. When it was time to inspect a critical pipeline constructed back in 1960, that had never been pigged before, was subject to modification in between time, and, with no original pipeline construction data, the operator needed a low-risk approach to prove piggability prior to implementing their ILI campaign. Crossing the Appalachian mountains like a rollercoaster, the last thing they wanted was a lost or stuck pig.
This paper outlines the pigging strategy and practice employed to ensure successful pipeline preparation ahead of metal loss inspection in 64-year-old pipeline that had never ran a pig. Using the Pathfinder foam bodied caliper tool to provide a baseline geometry survey supporting initial bore proving and debris mapping, identified, sized and located a lot of unknown and unexpected features and anomalies, including over 70 dents, several hundred bends and significant areas of debris build up. The survey data was used to provide assurance for pre-inspection cleaning pig selection, provide piggability assurance and qualify line cleanliness as part of the operators pipeline pigging strategy prior to running a metal loss inspection.
The presentation demonstrates the effectiveness of a progressive and innovative approach using a foam bodied caliper tool to qualify pipeline proving and cleaning resulting in a flawless ILI survey, executed safely without any unplanned operational deferment or constraint.
Ahmed Hassanin1, Atul Ganpatye1, Brian Yeung2, Tommy Mikalson2, Brett Conrad2
1ADV Integrity, Inc., Magnolia, USA. 2TC Energy, Calgary, Canada
Girth welds joining pipes/components of dissimilar wall thicknesses exhibit higher stress concentrations at the wall thickness transition region, significantly affecting their fatigue performance and limit load capacities. In addition, the presence of flaws in these welds exacerbate the stress concentration, potentially further degrading their performance. Therefore, when flaws are detected in girth welds, assessment and remediation becomes critical to ensure safe operation.
This paper discusses a case study that utilized numerical and experimental methods to assess the performance of girth welds when the pipe segment is subjected to high strain – low cycle axial loads that result from environmental forces. Additionally, the effectiveness of girth weld reinforcements such as steel sleeves, composite wraps, or a combination of both are examined to evaluate the benefits to the fatigue life.
Numerical analyses involved simulating a typical girth weld using finite element (FE) models to assess the localized stresses and stress concentration factors, with and without reinforcements. Various scenarios were examined, including different wall thickness transition ratios, material mismatches, and repair installation pressures, aiming to evaluate the effectiveness of repairs in reducing stresses and enhancing the fatigue life of the weld.
Testing encompassed sub-scale, small-scale, and full-scale tests aimed at validating the performance of the girth weld with and without reinforcements. Sub-scale and small-scale testing results were coupled with the numerical analyses results to design and execute the full-scale test, which simulated the real-life behavior of the girth weld in the field.
The paper discusses the details of the numerical and testing methods and demonstrates the effectiveness of the reinforcements in improving the fatigue life of girth welds.
KEYWORDS: Girth Welds, Geohazard, Fatigue, Numerical Analysis, Experimental Testing, Pipe Reinforcement, Steel Sleeve, Composite Repair, FEA, Full-Scale Testing
Thomas Beuker1, Felipe Freitas2
1ROSEN, Lingen, Germany. 2ROSEN, Houston, USA
EMAT technology has been established as a viable method for In-Line Inspection (ILI) of pipelines. Recently, the practices in the industry for increasing sensitivity regarding axial crack detection has been connected to the emerging fuel discussion, such as hydrogen and its potential influence on cracking. In addition, the maintenance of existing assets can also benefit from an optimized hydrotest and dig programs through an improved ILI approach.
The presented new EMAT Ultra technology builds upon the existing technology and allows a seamless integration of existing experiences and workflows. The sensor coverage for this ILI technology has been doubled to achieve redundancy and a dual sound path approach (CW, CCW). In principle, the detection reliability for cracks with critical dimensions has been improved beyond the industry’s current standards to 95% (POD). This paper presents the performance of this new technology based on industry standards and highlights the results obtained from several pipeline inspections. This technological improvement aims to contribute positively to the pipeline industry by fostering innovation while respecting the robust foundations laid by the existing EMAT technology.
Patricia Varela, Alexander Mckenzie-Johnson
Geosyntec Consultants, Inc., The Woodlands, USA
Landslides are present in every state of the USA and every province in Canada, and the extensive transmission, distribution, and gathering pipeline network is vulnerable to impacts from landslides, including pipeline rupture. Based on PHMSA statistics, landslides are one of the most expensive causes of pipeline rupture and result in more onshore pipeline ruptures than all other natural force incidents combined. For these reasons, considerable focus has been put on managing landslide hazards, such as PHMSA advisories ADB-2019-02 and ADB-2022-01, and the recently released API RP 1187. The traditional framework to address landslide hazards, as summarized in API RP 1187, starts with a system-wide desktop screening of geohazards (Level 1) and ends with site-specific detailed investigations (Level 3).
To enhance the desktop Level 1 Assessment process, Geosyntec has partnered with several North American pipeline operators to develop three novel methods to produce landslide susceptibility maps and inform decision-makers about the exposure to this geohazard. These landslide susceptibility methods not only map existing landslide hazards as is traditionally performed at Level 1 as described in API RP 1187, but they also predict areas that may be more likely to experience future landslide activity in response to forcing events, such as significant precipitation (e.g., rainfall or snowmelt) or topographic change (such as from naturally occurring erosion or construction). These methods use various combinations of high-resolution LiDAR, soils, and geologic mapping produced by public agencies and subject matter expert (SME) input. This paper discusses these three methods, which combined to date, have been implemented along more than 18,000 miles of pipelines in the United States and Canada. Additionally, this paper discusses how the resultant landslide susceptibility maps are and can be used to design or refine pipeline management practices, such as pipeline integrity assessment, budgeting, risk modeling, and construction planning.
Lautaro Ganim1, David Classen1, Oscar Gualdron2, Jaime Aristizabal2, Edwin Moreno1
1Baker Hughes, Houston, USA. 2CENIT, Bogota, Colombia
Nowadays the use of inertial measurement unit (IMU) derived bending strain data to identify and assess pipeline movement events due to geohazards has become a standard process. Service providers and operators should also be aware of the limitations of this process and the complementary analysis that is required or necessary to provide a complete picture of the threat. Understanding the results of the IMU bending strain analysis (pipeline movement included) and going further to obtain a deep knowledge between what is shown in the graphical information and what is occurring in the pipe-soil interaction makes a real difference. For this reason, the interaction between pipeline operator and In Line Inspection (ILI) service provider is a crucial part of effective geohazards management.
In this paper, two case studies will be presented where the complexity of geomorphological conditions interacting with the pipeline dictates that more comprehensive investigation and assessment methods are necessary to ensure effective understanding of the pipeline condition and the impact of geohazards. Oil transportation through a mountainous region is a challenge, even more so if there are areas with known active landslides, extreme weather conditions and earthquakes. The use of special construction and mitigation techniques, like casings, supports or even concrete structures could lead to a more complicated scenario compared with a pipe-soil interaction only.
The first case study describes a section of a pipeline under a special type of casing built to mitigate pipe-soil interaction in an area with known landslide occurrences and monitored by the operator to identify and measure ground movement. Thanks to an expert assessment and additional interpretation of the strain plots combined with the use of high-resolution reporting thresholds, the extension of the displaced area was accurately correlated and measured. This specific case led to an improvement in the analysis process.
The second case study involves a pipeline running through the toe of a hill with no report of geotechnical activity (taking other inspection techniques into consideration) or need for any mechanical remediation. However, two wrinkle-type anomalies were reported by the ILI geometry analysis. After a detailed review of the tool angle variation from previous inspections, the nature of these anomalies was compared to the kinematics of ground movement, and the wrinkle-type anomalies were verified, with an axial load component, in subsequent on-site inspections.
Michael Kobelak1, Arvind Chaabra2
1Intero Integrity, Toronto, Canada. 2Enbridge, Toronto, Canada
The identification and management of dents and mechanical damage / deformation is an ongoing challenge for pipeline operators. Apart from excavating and examining, performing in-line-inspection is typically required to detect and size dents.
To exceed the mandated standard, Enbridge initiated targeted assessments on a subset of distribution pipes to gain focused insight on pipeline health. These pipelines are located in both urban and agricultural terrain which can increase susceptibility to 3rd party damage.
This paper will review the ILI tool selection process, execution, and the integrity results focusing on Intero’s Laser Deformation Sensor (LDS).
The laser-based system provides a high-resolution dataset by projecting a continuous laser ring inside the pipeline. This allows for profiling dents with complex geometry (such as multi-apex and skewed dents) and supports further advanced processing including strain analysis using the ASME B31.8 standard.
McKenzie Kissel1, Keila Caridad2, Aaron Schartner3, Neil Shortt3, Jose Fernando Vazquez2, Pu Gong1, Stephen Westwood1
1Onstream Pipeline Inspection, Calgary, Canada. 2TC Energy, Mexico City, Mexico. 3TC Energy, Calgary, Canada
TC Energy operates a 430 km (267 mile) NPS 24 pipeline through the Sinaloa state of Mexico, supplying natural gas to a main client power plant near Mazatlán. The system is configured with a compressor station 500 km (310 miles) upstream of the NPS 24 pipeline, and the final compressor station is located at the end of the pipeline near the power plant. This compressor configuration results in the system operating with low differential pressure along the line and flows that are dependent on the client’s demand.
Due to the unique operating conditions, inline inspection (ILI) of the system can be unpredictable and challenging, requiring an engineered approach since standard ILI methods may not be sufficient. This paper describes the collaboration between the operator and ILI vendor, and the ILI vendors approach to successfully inspect the line. An optimized ILI Magnetic Flux Leakage (MFL) TriStream combo tool was utilized, reducing the tool differential pressure requirements by more than 66% and allowing navigation of the pipeline at low differential pressures, while still providing validated Ultra-High resolution Triaxial sizing specification.
Sarah Newton1, Caroline Scheeval2
1Cambio Earth Systems, Calgary, Canada. 2BGC Engineering, Golden, USA
In line inspection (ILI) inertial measurement unit (IMU) bending strain features can provide key insights for early detection of geohazard risks to pipelines. A program of regular IMU data collection yields significant quantities of data. Appropriate organization, analysis, and integration with other key datasets enables integrity managers to maximize their returns on investing in this data collection. Earlier publications have shown that IMU detects key change at around 50% of all critical geohazard sites (Van Hove et al., 2024). This paper explores a novel approach of applying a data model to IMU data that both geospatially organizes the data and integrates the data with lidar, lidar change detection, InSAR, geohazard inspections, landslide hazard mapping, and instrumentation data. The data model establishes the relationships between ILI runs, bending strain reporting, IMU bending strain features, and IMU bending strain inspections. A software platform is used to visualize these data and enable workflows to enhance geohazard threat detection, assessment, and monitoring. Data associations are established with the geohazards threats such that analysts can easily investigate the geohazard and IMU bending strain feature histories, recommend and track next actions, and monitoring changing conditions that could accelerate geohazard activity and impact the pipelines. This approach is currently in use by 10 pipeline operators in the United States and Canada.
KEYWORDS: Geohazards, Data Management, Integrity Management Plans, ILI analysis
Shenwei Zhang1, Rick Wang2, Ji Bao3
1TC Energy, Calgary, Canada. 2TCEnergy, Calgary, Canada. 3Pembina, Calgary, Canada
Mechanical damage poses a significant safety risk to the structural integrity of oil and gas steel pipelines. Fatigue due to cyclic loading is one of leading causal factors to failure for pipelines, particularly for oil pipelines, subject to mechanical damage in the form of dent or dent with gouge. Many fatigue assessment models were developed and published in the industry to evaluate the remaining life of dented pipelines. These models include the API 1156 model, EPRG 1995 and 2000 models, Petrobras model, BS 7608 model, API 1183 screening and assessment models as well as some most recently developed models through the PRCI projects. The objective of this paper is twofold. Firstly, it provides an overview of the existing models and the comparison of these models through parametric analysis. Secondly, it presents the accuracy and precision of these models by comparing the predicted fatigue life and the experimental fatigue life. The study reported in this paper will facilitate the application of the fatigue assessment models and benefit operators for optimizing their integrity management program of pipelines subject to mechanical damage.
KEYWORDS: pipeline, mechanical damage, dent, gouge, fatigue
Lucinda Smart, Benjamin Wright
Kiefner and Associates, Ames, USA
The concept of in-line inspection (ILI) tool validation could be succinctly summarized as follows: identify dig locations based on ILI reported features, measure these features in the ditch, compare in-ditch results with ILI predictions, log the results for future ILI assessments at specified intervals, and then proceed to the next pipeline segment. However, the complexities involved in ILI tool validation make it interesting. Each pipeline and ILI run is unique, presenting its own set of challenges that must be addressed.
This paper will discuss a case in which a pipeline underwent a repeat axial magnetic flux leakage (MFL) ILI runs, which reported thousands of defects of varying geometries and depths. The focus will be on the efforts that may be performed to validate this tool run and to ensure the pipeline’s safety for continued operation.
Understanding the levels of validation as outlined in API 1163 is essential in whether the tool run can be deemed validated. When validation digs are performed to assess tool performance, particularly when there is a wide array of defects reported, it is important to account for the types of defects that may be found and to have appropriate technology available to capture these defects. There are many facets that can be explored with more data, and handling that appropriately can be a challenge. The results can give a wealth of insight into the tool’s performance and the condition of the line. This paper will provide recommendations on what factors an operator should consider when obtaining a large data set of correlated features from validation digs. Understanding ILI tool performance and the true condition of the pipeline is critical to maintaining the integrity of pipeline assets.
Christopher Davies, Johannes Spille, Simon Slater
ROSEN USA, Houston, USA
Managing the assorted threats associated with pipelines is an evolving process. Selective seam weld corrosion (SSWC), while not a new threat, is now receiving increased scrutiny amid existing and new regulatory requirements.
SSWC tends to have a complex morphology, with a relatively high length-to-width ratio compared to general corrosion and a localized area of maximum depth described as a V-shape. SSWC creates a significant risk for operators because it is more difficult to detect, classify, and size using established in-line inspection (ILI) technology. Furthermore, well-established methods to assess the severity of the corrosion may not be appropriate. Operators often manage the threat through a combination of low specificity ILI assessments and in-ditch validation. However, when many ILI metal loss indications coincident with the longitudinal seam weld are identified, establishing an effective and efficient response can be challenging.
Over the past two years, a significant body of data from ILI, field excavations and metallurgical verification has been captured to evaluate and help improve technologies for detecting and characterizing SSWC. In combination with updated regulatory requirements and inspection specification improvements, this has brought renewed attention to the question of how the threat of SSWC can be managed.
This paper highlights the results of recent pull tests used to help develop an improved performance specification for the circumferential magnetic flux leakage Ultra tool (MFLC Ultra) currently offered to more effectively manage the threat of SSWC. Examples illustrate how collaborative efforts performed by operators have been used to refine probability of detection (POD) and probability of identification (POI), with a focus on differentiating SSWC from coincident corrosion crossing the long seam.
Leveraging existing guidance regarding the management of the threat of corrosion on the long seam, this paper also presents the results of extensive nondestructive and destructive testing of validated SSWC anomalies. The goal is to share learnings and discuss the considerations for assessing these anomalies in order to identify an appropriate response based on all the information available to the operator.
Simon Slater1, Christopher Davies1, Sean Moran2
1ROSEN USA, Houston, USA. 2Williams, Salt Lake City, USA
Since the introduction of guidance pertaining to Engineering Critical Assessment (ECA) in gas regulation, operators have been grappling with exactly what is required to complete an ECA and the question of what good looks like? Over the past few years, there has been intensive discussion between the regulator, operators and service providers. This open dialogue and collaboration, combined with operators actively working on ECA’s, has paved the way for a clearer understanding of what is required. The regulatory language has been digested to define a transparent laundry list of tasks and data requirements required to close an ECA. Engagement with the regulator has helped add color to the outlines given in regulation, with appreciation on the timelines and milestones expected to complete an ECA. There are several significant tasks that require focus early in the process to establish a successful path, and planning is key. This paper will discuss the current and established route for ECA’s used to reconfirm MAOP and conclude by identifying when an ECA can be considered complete and taken credit for in relation to the deadlines of 50% of 192.624 covered segments by 2028 and 100% by 2035.
Michael Rosenfeld1, Bill Amend1, Simon Slater2
1RSI Pipeline Solutions, New Albany, USA. 2ROSEN USA, Columbus, USA
Pipe body hard spots have been recognized as a pipeline integrity threat in certain types of vintage line pipe, causing ruptures, leaks, and near-miss events. Hard spots can now be managed within the template of Integrity Management, including susceptibility and threat assessment, whether and when to perform a baseline assessment, in-line inspection, prioritization of assessment response, field examination, acceptable hardness limits, repair decisions, reassessment decisions, and mitigations. This paper discusses key factors, recommendations, and pitfalls to consider in the integrity management process. However, industry knowledge and experience is evolving, and important gaps remain. Areas for further development to address current knowledge gaps are also discussed.
KEYWORDS: Hard spots, vintage pipelines, integrity management, threat assessment
Sheri Baucom
OneBridge Solutions, Durango, USA
With over 11,000 assessments on 400k miles of pipeline from 18 pipeline operators and 34 inline inspection (ILI) service providers, OneBridge Solutions (OBS) has amassed the largest and most diversified set of ILI data in the industry. This paper presents insights gleaned from the analysis of said ILI data, with the focused aim of determining what variables contribute to high ILI system performance i.e. ILI service provider, ILI technology, pipeline operator, product, experience of the ILI service providers, etc. These insights are presented to achieve the foremost goal of shared learnings amongst all stakeholders and provide valuable information that pipeline operators can utilize to improve their pipeline integrity program.
Simon Slater, David Bastidas
ROSEN, Houston, USA
The energy transition has gathered momentum stimulating the natural gas industry to swiftly adapt to the evolving energy ecosystem, driven by the need to reduce carbon footprint and seek alternative fuels like H2. In the last five years, there has been a significant increase in industry focus and research within the natural gas and hydrogen pipeline sectors. Gaps have been identified in the current technical standards for repurposing of natural gas pipelines for hydrogen gas. Neither ASME B31.8 nor ASME B31.12 effectively address the issues faced by transmission and distribution pipeline operators seeking to integrate hydrogen gas into the existing natural gas infrastructure. In this regard, Consensus Engineering Requirements (CERs) have been elaborated to provide practices for H2 and H2 blends pipeline services, aiming to be the basis for new guidance within ASME B31.8 code. The intent of the approach is to provide a robust analytical method for users to qualify pipelines for safe operation in H2 commensurate with the asset specificities, alongside operational envelope, rather than using prescriptive approaches. This paper will discuss the guidelines created for repurposing within the CERS, which are proposed for inclusion in the 2026 version of ASME B31.8.
Carlos Diaz, Rick Desaulniers
ENTEGRA, Indianapolis, USA
Hard spots are typically associated with older pipelines. A recent joint industry research initiative, however, is revealing that hard spots may occur in a wider variety of pipeline vintages, sizes and manufacturing sources than previously thought.
Hard spots can pose a major threat in pipelines, and some have led to dangerous ruptures. Legacy ILI technology was unable to detect hard spots or characterize them with confidence. Inconclusive data might mean hardness is underestimated, leaving pipes unexpectedly vulnerable to cracking in the presence of other corrosive factors. This can be especially concerning as many lines transition to hydrogen transmission.
Carlos Diaz, ENTEGRA Account Manager, and Rick Desaulniers, ENTEGRA Chief Data Scientist, will discuss preliminary findings from this joint research program, which was undertaken in partnership with multiple operators and utilized the Pipeline Research Council International (PRCI) technology center.
They’ll showcase how the ENTEGRA® Ultra High Resolution (UHR) ILI system aids in detection and detailed characterization of hard spots, including assigning more accurate Brinell ratings. They will also share the importance of looking for hard spots in pipes that aren’t often associated with this anomaly, explore how this project uncovered different types of hard spots, and how the findings from this research may lead to changing protocols for hard spot detection.
KEYWORD(S): ILI Analysis, Hard Spots, Pipe Vintage, Manufacturing Anomalies, Emerging Research
Omar Al Ghamari, Madjid Afshari
OQGN, Muscat, Oman
OQ Gas Networks (OQGN) is the exclusive operator of Oman’s natural gas transportation system comprising a network of around 4,500 Km of pipeline that supply gas as fuel and feedstock to many customers across Oman. One of OQGN pipelines, is a 10" pipeline that is crossing the capital city (Muscat) to one of the customers in high population area. The pipeline was commissioned in 2007, with a total length of 40 Km. Throughout the years, the pipeline has been suffering from external corrosion which resulted in a deration from 92.0 Barg original design to 66.0 Barg. All the locations affected by external corrosion are located at the field joint area due to Heat Shrink Sleeve failure.
Since construction in 2007, the first heat shrink sleeve failure was observed on 2014 ILI, that is after 7 years in operation only. The corrosion rate of those defects various from one location to another, however the maximum localized corrosion rate was calculated approximately 0.3 mm/y. As the pipeline has a low thickness of 4.6 mm, operating the pipeline with this corrosion rate make it critical in terms of inspection, integrity assurance and repair strategy.
Since 2014, a total number of 4 ILI runs were done. Analyzing defects growth based on consecutive runs didn’t show any trend as corrosion rate was not linear and even in some cases no growth detected therefore corrosion growth rate is difficult to predict. The used heat shrink sleeve material was approved as per ISO 21809-3 system 14B (cross-linked heat-shrinkable polyethylene-based material). While the same product has been applied in other pipelines, only this pipeline suffers from premature HSS failure mainly due to application qualification issues.
Subject pipeline protected by impressed current cathodic protection however, the disbandment of HSS results in a creation of corrosion cell beneath the coating, and as PE is shielding the CP current, no protection provided to the pipeline, hence, the pipeline is experiencing accelerated soil corrosion rate.
This paper is focusing on the current approach that OQGN is adapting to maintain the 10" mechanical integrity by interfacing both ILI frequency optimization, corrosion rate monitoring and field joint coating rehabilitation program.
KEYWORDS: Pipeline ILI, Heat Shrink Sleeve Failure, Pipeline Repair, Defect Assessment, Coating Rehabilitation
Anthony Tindall1, David Classen2
1Baker Hughes, Cramlington, UK. 2Baker Hughes, Houston, USA
Magnetic Flux Leakage (MFL) inspection was the first technology introduced in the 1980’s to routinely inspect oil and gas pipelines for corrosion defects, and today it remains the most trusted In-line Inspection (ILI) technology for that purpose. Thousands of MFL inspections are carried out by ILI vendors each year ensuring pipeline operators can effectively manage their corrosion integrity programs.
Since the introduction of high-resolution axial MFL inspection vehicles, there has been a substantial number of improvements in capabilities. These include inertial mapping units (IMU), speed control, increased sensor density and combination sensing (caliper, eddy current, transverse MFL and triaxial MFL measurement).
Even with these advances, surprisingly most MFL inspections only measure and use one of three components of magnetic flux field leakage that occur at a corrosion feature when magnetized by the inspection tool at a localised thinning of the pipe wall. However, it is well proven that different corrosion morphologies will trigger significantly different leakage in these components. These characteristic signatures consequently provide an additional and robust means to identify corrosion profiles and interactions that in many cases are not detectable or distinguishable when using only a single axis – no matter how high the sensing resolution the inspection tool may have. Optimising sensor resolution in combination with measuring all three leakage components offers clear advantages, particularly when defect morphologies become challenging.
This paper will provide a deeper insight as to how the three independent leakage components provide unique identifiers that can be used to accurately size pin holes, axial and circumferential slotting, and importantly de-construct complex morphologies and be used more effectively in the analysis process to improve POD, POI and POS. These identifiers not only ensure correct corrosion interpretation, but also that these defect types are identified correctly within the often hundreds of thousands of features within many miles of pipeline.
The paper will conclude with a demonstration of how, in combination with monitoring of data accuracy for every validated inspection conducted, the adoption of data accuracy results as a key performance indicator can be effectively employed to target and drive continuous improvement of even the highest performing inspection technologies.
Michelle Unger1, Karen Collins2
1ROSEN GROUP, Newcastle upon Tyne, UK. 2ROSEN GROUP, Houston, USA
The pipeline industry has long recognized the critical importance of establishing competency and qualification standards to ensure the safety, reliability, and integrity of pipeline operations. The journey toward internationally accredited certifications began by addressing the limitations of traditional competency measures, such as IQ tests and personality assessments. Instead, the focus shifted to developing competency-based frameworks specifically tailored to the pipeline industry, emphasizing the ability to perform tasks to a recognized standard and the need for practical, job-specific qualifications. This foundational phase established key competency elements and standards, guided by international standards like ISO 13623 and ASME codes, ensuring that qualified and competent personnel are engaged across all stages of pipeline activities.
The journey then progressed into the development and implementation of a structured certification process. This phase was marked by creating a qualification ‘route map’ that integrated competency-based learning programs with objective assessments. Extensive collaboration with industry experts led to the development of robust learning guides and digital learning platforms that facilitated knowledge transfer and continuous professional development. Rigorous competency assessments were also introduced to ensure that the certifications awarded reflected genuine expertise and aligned with industry standards.
The culmination of these efforts was achieving international ANAB accreditation for pipeline integrity certifications. This milestone marked the successful transition from theory to practice, establishing a new global standard for pipeline competency certifications. The widespread implementation of eight ANAB-accredited certifications in critical areas of pipeline integrity management has set a new benchmark for the industry, providing a clear and structured path for professionals to achieve and demonstrate their competency.
This paper showcases the evolution of competency certification in the pipeline industry, underscoring its transformation from concept to a robust, globally recognized standard that ensures the highest levels of safety and expertise in pipeline operations.
Ryan Stewart1, Jason Skow1, Ryan Okamura2, Mohammad Al-Amin2, Zain Al-Hasani3, Luigi Calabretta2
1Integral Engineering, Edmonton, Canada. 2TC Energy, Calgary, Canada. 3TC Energy, Houston, USA
The methodology outlined in this study aims to quantify the ability of ILI tools to identify and classify transmission pipeline segments into populations with unique material properties for the purpose of achieving compliance with PHMSA’s material verification requirements. The framework uses statistical methods similar to those outlined in API 1163 (2021) for ILI measurement validation which have been used by the industry for twenty years.
49 CFR §192.607 defines unique populations for pipeline material verification. These include diameter, wall thickness, pipe grade, manufacturing process, manufacturing date, and construction date. ILI tools, such as Rosen’s RoMat™, have shown promise in identifying yield strength and ultimate tensile strength. Using ILI to identify pipe attributes has the potential to significantly improve the efficiency of satisfying the material verification requirements outlined in 49 CFR §192.607.
The methodology to identify unique pipeline populations examined in this paper is a process where ILI measurements are combined with subject matter expert (SME) judgement. This process, while effective, introduces variability from SME discretion and ILI measurement error, particularly when patterns in the ILI data are not conclusive from systematic statistical methods. Furthermore, some of the ILI technologies used in this process are relatively new, and ILI vendors do not yet provide a performance specification for their performance in identifying populations.
This analysis explores a heuristic rule to quantify SME judgments and incorporates them into a probabilistic model specification for ILI population identification. The models were fit using populations identified by the ILI vendor and validated using records review and field verification by an operator. These models are designed to estimate the accuracy of future population identifications and highlight populations that are more likely to be misclassified, thereby informing an operator’s decision-making to prioritize validation efforts.
Amir Ahmadipur, Ali Ebrahimi
Geosyntec Consultants, Houston, USA
Stress relief excavation is a landslide mitigation method in which the pipeline segment affected by a landslide is exposed to allow for pipeline rebound and release of a portion of the accumulated elastic strains on the pipeline caused by the landslide. The procedure of stress relief excavations is relatively well-established. Pipeline rebound during stress relief excavations are sometimes measured through frequent measurements of survey laths installed at certain intervals tangent to either side of the pipeline. In some cases, strain gauges are installed on pipelines prior to the stress relief excavation to monitor the strain change during stress relief excavation. Another way to evaluate the effectiveness of a stress relief excavation is to compare the run-to-run bending strain measurements using Inertial Measurement Unit (IMU) before and after the stress relief excavation. Most of the times, at best, only one of these measurement approaches is available to evaluate the effectiveness of the stress relief excavation. Case studies having 2 or more of these approaches are not very common; however, when available, they can provide valuable information to the pipeline industry on the effectiveness of the stress relief excavation to reduce the strain demand on pipelines. Such information can also assist pipeline operators with decision making about stress relief excavation versus pipe cutout and replacement or other potential mitigation measures.
This paper presents the data collected during and after stress relief excavations at four landslide sites in the USA. These case studies include a variety of situations in which the stress-relief excavations were performed. The collected information includes pipe rebound measurements using survey laths, strain change measurements during and after stress relief excavation from strain gauges when available, and strain change comparison before and after the stress relief excavations using Inertial Measurement Unit (IMU) measurements.
Arnav Rana1, Sanjay Tiku1, Ali Roostaei1, Behrouz Shiari1, Vlado Semiga1, Aaron Dinovitzer2, Munendra Tomar3, Yohann Miglis4, Mark Piazza5
1BMT Canada, Ottawa, Canada. 2ADIM Consulting, Ottawa, Canada. 3TC Energy, Houston, USA. 4Kinder Morgan, Houston, USA. 5API, Washington DC, USA
Dents or mechanical damage in buried pipelines can occur due to a number of potential causes; the pipe resting on rock, third party machinery strike, rock strikes during backfilling, amongst others. The long-term integrity of a dented pipeline segment is a complex function of a variety of parameters including but not limited to pipe size, indentation depth, dent or indenter shape, indenter support, pressure history at and following indentation. Operational experience and regulatory oversight have identified mechanical damage as a significant threat to pipeline integrity. In response to this threat, industry has sponsored mechanical damage research (i.e., PRCI, US DOT PHMSA, CEPA, and others) and industry lead by the American Petroleum Institute (API) developed a recommended practice for managing pipeline mechanical damage (API RP 1183). The first edition of API RP 1183 was assembled and published in 2020 by drawing together industry experience and engineering tools available at the time recognizing that improvements would be possible. With use, opportunities for improvement in API RP 1183 have been identified and thus a second edition of the recommended practice is being considered at this time.
This paper is offered to discuss the opportunity for improvement (OFI) observations that have been offered in the open literature related to the tools and techniques presented in API RP 1183. The observations are related primarily to the recommended practice (RP) restraint condition, indentation strain and fatigue screening and analysis tools. The paper will address a range of OFI’s, including but not limited to:
The objective of this paper is to provide engineering or science-based answers to the questions raised related to API RP 1183 mechanical damage management procedures and demonstrate while there are opportunities for improvement, the engineering tools presented in API RP 1183 provide a sound basis for mechanical damage management in pipelines.
Kachi Ndubuaku1, Brendan Eirich2, Kristian Olsen3
1Enbridge, Edmonton, Canada. 2ATCO, Edmonton, Canada. 3Stantec, Edmonton, Canada
Mild ripples may be introduced in pipelines prior to installation, during the process of forming field bends. Wrinkles/buckles may also develop in pipelines under monotonic displacement-controlled loading conditions, such as permanent ground deformation. Many pipeline industry codes define the acceptability of surficial deformations in energy pipelines based on generic serviceability limit criteria such as adverse effects of wrinkles on the integrity of pipe coating or impairment of in-line inspection. However, the codes do not provide explicit guidance on the acceptance standards with regards to the effect of surficial deformations on the structural/mechanical performance and long-term integrity of pipelines. A powerful transformation tool is presented in this paper to approximate the deformed centerline profile, as well as surface deformities, of pipelines using high-resolution ILI IMU/caliper data. The tool provides interactive 3D visualization of the deformed pipeline therefore allowing proper categorization of the observed deformities, and also evaluates the longitudinal and circumferential bending strains over the full pipeline surface. The tool also generates the 3D surface mesh needed as input for more advanced finite element analysis (FEA), including pipe-soil interaction properties required to properly simulate buried conditions if applicable. Ultimately, a systematic approach is outlined herein for using the analytical strain estimates generated by the transformation tool, combined with the results of FEA, as input for performing level 3 fitness-for-service fatigue-life assessment of wrinkled pipelines.
Rick Wang
TC Energy, Calgary, Canada
Pipeline dents, caused by external indenters applying force to the pipeline surface, are a major integrity concern due to their potential to cause immediate or delayed failures, depending on their severity, operating conditions, and other factors. Traditionally managed by In-Line Inspection (ILI) tools, evaluating and prioritizing critical injury dents that require immediate action remains challenging. This paper presents a practical assessment approach for operators, combining a dent strain-severity criterion with Magnetic Flux Leakage (MFL) signal recognition to identify dents with corrosions, gouges and cracks. Additionally, an enhanced method for distinguishing between plain dents and those with gouges or cracks, particularly for topside dents, is discussed. Case studies are provided to demonstrate the effectiveness of this approach in identifying critical injury dents that necessitate immediate investigation.
Travis Cust1, Neil DeVetten2
1Quest Integrity, Calgary, Canada. 2TC Energy, Calgary, Canada
Small-diameter, difficult-to-inspect, or unpigable pipelines have limited inspection options in their Integrity Management tool kit. When the threats of concern are cracking-related, such as Stress Corrosion Cracking (SCC), the available options are usually limited to Hydrotest or Direct Assessment (SCCDA). This paper presents a case study on the pivotal role that bidirectional tethered In-Line Inspection (ILI) tools can bring to pipeline integrity programs. It will provide an overview of a recent tethered inspection of an 11.9 km NPS10 lateral natural gas pipeline, employing multiple cut points and a bidirectional EMAT (Electromagnetic Acoustic Transducer) ILI tool.
Designed for pipeline operators, integrity engineers, ILI coordinators, planners, and construction managers with intermediate to advanced technical expertise, the session will first address the operational challenges that bidirectional tethered ILI solutions can effectively resolve. Following this, the EMAT technology and its application in performing a multi-cut point bidirectional tethered inspection will be reviewed, along with the challenges encountered during the process and the key lessons learned. This examination aims to provide actionable insights and advancements in pipeline inspection technology utilization and threat detection.
KEYWORDS: EMAT technology, “Unpiggable” inspections and technologies, SCC assessment and management
Janille Maragh1, Emily Brady2, Jeffrey Kornuta2, Owen Lopez-Oneal3, Peter Veloo3
1Exponent, Inc., Menlo Park, USA. 2Exponent, Inc., Houston, USA. 3Pacific Gas & Electric Company, Oakland, USA
Federal regulations governing gas transmission pipelines allow nondestructive (NDT) or destructive testing (DT) techniques to verify the material properties of pipe joints. As part of its material property verification program, the Pacific Gas & Electric Company (PG&E) routinely performs pipe grade determination using NDT strength and chemical composition measurements with associated uncertainty values. Over the course of several years, PG&E has also assembled a database of DT data for pipe joints, which includes data for pipe joints both with and without known pipe grade. For the pipe joints without known grade, it is desired to determine the pipe grade to update PG&E’s system of record. Any DT measurements have some degree of uncertainty associated with them that should be accounted for in the pipe grade determination process. However, DT data obtained for pipe joints may not include replicate measurements that could be used to estimate uncertainty (i.e., standard deviation), usually due to the cost and labor required to obtain that data. Therefore, we developed an alternative process to determine reasonably conservative uncertainty values for DT strength and chemical composition measurements.
For this process, we reviewed scientific and engineering literature, testing standards, and instrument manufacturer technical documents. We then obtained or calculated uncertainty values based on the literature and chose reasonably conservative uncertainty values within the element concentration ranges typically observed in low carbon pipeline steels. Additionally, we analyzed PG&E’s historic database of DT measurements and used a subset of the database, which consisted of DT chemical composition and strength data for 633 pipe joints with known grades, to validate our proposed uncertainty values. We did so by comparing the predicted pipe grades calculated using the DT measurements and the proposed uncertainty values with the known pipe grades. This validation process was also used to assess the sensitivity of pipe grade predictions to uncertainty values.
Alan Cornejo1, Martin Melucci1, Brian Kerrigan2, Dom Murray2
1TGN, Ciudad Autonoma de Bs As, Argentina. 2Frontline Integrity, Newcastle, UK
The main goal of any pipeline operator managing an active cracking threat is to find the real cracks and minimize costly verifications of false positives. Crack detection In-Line Inspection (ILI) is commonly deployed by operators as the primary integrity assessment technique to manage axial Stress Corrosion Cracking (SCC) due to its coverage and relative convenience. Whilst these tools can be excellent at detecting planar crack-like reflectors, the performance specification typically states that there is no guarantee that a reported crack-like reflector will be an actual crack with time-dependency, which could pose a threat to a pipeline’s integrity.
This paper presents how a natural gas transmission operator in Argentina has leveraged their extensive ILI and field database to benchmark a predictive, data driven process to support the management of stress corrosion cracking in-line with API 1176 along their network and minimize the number of future verifications of false positives, allowing focus on real integrity threats.
Xavier Ortiz, Sean Prestie
Imperial Oil Ltd, Calgary, Canada
Pipeline operators face several challenges during the implementation of a seam cracking integrity management program (IMP). Some of these challenges are related to improving the confidence on NDE dig data, ILI tool data analysis and crack sizing, and implementing crack assessment methodologies under a risk-based assessment framework. Overcoming those challenges is key for the development of an effective and efficient dig program and long-term asset management strategy.
As part of the seam cracking IMP enhancements, Imperial Oil Ltd used a new and innovative crack detection tool that was developed and recently presented by ExxonMobil at the 2024 European Pipeline Technology Conference. Although the new ILI tool has shown to be highly accurate, the success of the enhanced seam cracking IMP was the result of the implementation of supporting integrity programs to ensure the right information and assessments were being used.
This paper and presentation will discuss the steps that were followed for the implementation of a successful ERW seam cracking IMP. Details about the new ultrasonic ILI technology with consistent and reliable tip diffraction sizing capability, the implementation of a structured NDE and validation program, the deterministic and probabilistic evaluation of reported seam weld anomalies using the PRCI MAT-8 methodology, and the implementation of a risk-based approach for dig selection and definition of a long-term seam cracking management plan, will be included in this document.
Katherine Hartl, Christoph Jaeger, Santiago Urrea, Christoph Seeber
NDT Global, Stutensee, Germany
In pipelines experiencing significant corrosion growth, frequent wall thickness measurements using In-Line Inspection (ILI) are beneficial. This paper defines ‘frequent inspections’ as those conducted less than a year apart. Increasing the frequency of these measurements allows for rapid assessment of mitigation measures’ effectiveness without the need for costly excavations. Ultrasonic ILI data enables evaluation on both a feature-specific and global scale. As corrosion rates decrease due to effective mitigation, inspection intervals can be extended. This paper explores three case studies at different stages of this approach.
The first case study addresses channeling corrosion, where frequent inspections were conducted until a reduction in corrosion growth rates was observed. The second case study examines pinhole corrosion, and the third case examines general corrosion. Both pipelines continue to be monitored frequently. Each case study is presented with statistical analysis of corrosion growth rates.
Additionally, operators rely on feature information spreadsheets as their primary view into the pipeline, which can be distorted by reporting practices. In the context of ultrasonic data, reporting only the deepest spot within a box may not adequately capture the extent of corrosion. This paper discusses reporting strategies for general and channeling corrosion to provide a more accurate representation.
KEYWORDS : ILI Analysis, ILI Applications, Corrosion Studies, Repair and/or Rehabilitation, Integrity Management Plans (IMP)
David Kania1, Ron Thompson2, Richard Kania3, Guillermo Solano2, Andrew Corbett2
1Novitech Inc., Calgary, Canada. 2Novitech Inc., Vaughn, Canada. 3KanEnergy Partners Inc., Calgary, Canada
The discovery of axial stress corrosion cracking (ASCC) in the 1990’s motivated the development of inline inspection (ILI) technologies capable of identifying and sizing these features with sufficient accuracy to support integrity programs. Along with ASCC, the discovery of Selective Seam Weld Corrosion (SSWC) has emerged in the past decade as a threat that sometimes exhibits crack-like behavior. In the case of both ASCC and SSWC, current ILI technologies continue to be challenged with the detection, characterization and accurate sizing of these features.
Novitech with its Micron ILI Technology® has designed and developed six primary sensor systems to address ASCC and SSWC anomalies. These sensor systems include CMFL-MF℠ (Multi-field Circumferential Magnetic Flux Leakage), AMFL-640℠ (Axial Magnetic Flux Leakage), IDD-SM℠ (Internal Depth and Stress Measurement), Micron-RF℠ (Residual Field for Crack Detection), Px2℠ (Precision Geometry Measurement) and industry standard Inertial Mapping unit.
The advanced flaw diagnostic approach with CMFL is combined with the extensive experience detecting and sizing other threats (metal loss, circumferential and off-axis cracking), demonstrating the ability to simultaneously detect, characterize and size both ASCC and SSWC threats in the same inspection campaign.
This paper explores the new CMFL-MF℠ multi-field sensor technology, which uses varying levels of magnetization with the mid-field part of the system used to mitigate the effects of flux leakage from shallow surface corrosion. By comparing the results from the full-field and the mid-field CMFL-MF℠ data, accurate characterization and sizing can be achieved.
Both the full-field and mid-field CMFL sensor systems have sampling densities of up to ١,٠٠٠ readings per square inch. When combined with the AMFL and other sensor systems the sampling density of the complete tool can exceed ٣,٠٠٠ readings per square inch.
Using the multifield CMFL approach along with the supporting data from AMFL-٦٤٠℠, high precision geometry, IDD-SM℠, Residual Field, and IMU mapping greatly improves the probability of detection (POD) and probability of identification (POI) of ASCC and SSWC, achieving very high probability of identification.
Detection and characterization of ASCC and SSWC from ٢٠٪ in depth and ١" (٢٥ mm) in axial length have been demonstrated in laboratory testing, pull testing, and in most recent live runs.
Dane Burden1, Adrian Belanger2, Ron Lundstrom1, Miguel Maldonado1
1TD Williamson, Salt Lake City, USA. 2TD Williamson, Houston, USA
The evolution of in-line inspection (ILI) tools over the last six decades has provided pipeline operators with continual growth of integrity management capabilities. While the core physics of many of these systems have remained fundamentally unchanged, there has been a significant progression from single-technology solutions to sophisticated, multi-technology frameworks. The last decade has increasingly enabled the integration of multiple, high-resolution sensor systems and coupled them with advanced digital technologies such as machine learning and artificial intelligence.
This paper will explore the progression of multi-technology ILI tools combined with the implementation of advanced computing techniques and how they have addressed complex and multifaceted problems within the pipeline integrity industry. Several case studies will be presented to illustrate the current capabilities for assessing common, complex, and unique integrity threats highlighting the value they bring to operators and the industry. Among these cases will be selective seam weld corrosion, mechanical damage (i.e. gouging and restrained vs unrestrained dents), hard spots, stress corrosion cracking and pipe material properties verification. Finally, the paper will explore potential future developments, looking at emerging trends, innovative integrations, and the anticipated impact on the industry.
Jeff Haferd1, Sylvain Cornu2
1Marathon Pipe Line, Findlay, USA. 2NDT Global, Stutensee, Germany
Pipeline geohazard identification, assessment, and mitigation remain critical areas of focus in the industry, with continuous advancements across multiple technologies. Effective geohazard management exemplifies the necessity for integrating new technologies to mitigate risks more effectively. Traditional approaches to geohazard management rely on a combination of IMU (bending strain), LiDAR, InSAR, Strain gauges and deformation platforms. Recently inline inspection (ILI) vendor(s) have developed novel strain measurement technologies designed to detect and measure the external loading caused by geohazards.
This paper reviews the successful technology validation to address the threat of geohazards to pipelines. A case study of a pipeline currently monitored for geohazard activity at multiple locations is included. The pipeline was inspected using a newly developed ILI strain tool (ETEC), with a specific focus on assessing how the inclusion of axial strain data can enhance the overall geohazard management program. The current program utilizes ground surveys, Lidar, ILI IMU bending strain, and strain gauge monitoring.
This review will demonstrate how the ILI strain tool data correlates to existing ILI IMU bending strain, with correlation to known geohazard sites currently being monitored using strain gauges. The ILI strain tool is capable of measuring bending strain based on curvature (IMU) and Magnetostrictive effect (ETEC). A distinction can then be made between loads induced by the environment versus those induced by construction. The subject pipeline undergoes regular inspections using ILI IMU, with pipeline movement/strain change analysis such that previous strain mitigation efforts can be assessed based on historical data. This historical data has also provided valuable insights into the pipeline’s current loading conditions.
The new ILI strain tool identified additional axial strain loading at known bending strain sites offering insights that were previously only inferable through simulation of the pipe at known bending strain areas. The second part of the review will show how the axial strain measurement identified additional geohazard locations where the bending strain was not present. The axial strain was predominantly detected over longer pipeline spans affected by landslides acting longitudinally, while bending strains were more common in shorter lengths where landslides moved transversely or oblique to the pipeline orientation.
Correlation between technologies allowed us to further refine the risk assessment across the potential geohazard sites and better estimate the strain demand on the pipeline. Finally additional correlation to known susceptible features, for example, circumferential cracks in tensile strain area, can be conducted to relate strain demand and strain capacity and help in prioritization of potential repairs.
KEYWORD(S): Geohazards, Strain, Bending, Eddy Current
Tim Rudd1, Carl Scott1, Brian Kerrigan2, Samuel Durand2
1Valero, Pembrokeshire, UK. 2FrontLine Integrity, Newcastle, UK
In today’s expanding world, pipeline operators are usually inundated with planning requests which interact with their pipeline right of way. In order to evaluate the potential impact on the pipeline and whether mitigation is required, each site requires a time-consuming analysis of the pipe materials, ground conditions, construction plans and above ground loads. This paper outlines how a liquid pipeline operator has digitally optimized a process that reviews load distribution requirements covering all credible scenarios along their system in line with API 1102 and other relevant standards.
Keith Leewis1, Daniel Ersoy2
1L&A Inc, Bragg Creek, Canada. 2Element Resources LLC, Princeville, USA
Previously, rule of thumb suggested that leaks only occur below 30% SMYS. Unfortunately, there have always been outliers below 30%. Catastrophic rupture conservatism was therefore assumed, and a high corresponding thermal radiation dosage in the PIR was estimated for static and non-static receptors. However, many breaches occur as leaks with a much reduced risk. This new methodology provides a reliable method to determine if the breach is a leak or rupture.
This Basic Rupture Framework (BR) methodology collapses a detailed seven-dimensional engineering analysis of more than ٣x١٠5 combinations into a simple two-dimensional plot. The BR methodology requires the operating pressure (default = MAOP) and an estimated a failure pressure (default = SMYS) to determine if the failure will be a leak or rupture. If a leak, then the BR consequence methodology will estimate a smaller, more realistic PIR and provide a better estimate of the actual consequences. This paper summarizes our PHMSA engineering report, describing how the BR Framework was developed and used to evaluate and plot >300,000 combinations of actual pipe attributes and operating conditions over decades of pipe to simplify the leak or rupture outcome.
Ken Maxfield1, Jeffery Knighton2, Phil Tisovec1
1KMAX Inspection, Salt Lake City, USA. 2ExxonMobil, Baton Rouge, USA
Recent updates to 49 CFR Parts 192 & 195 call for pipeline operators in the USA to comply with new regulations covering the construction and operation of their pipelines. These codes require that when a new line is constructed or when an existing pipeline is modified, it must be designed and built to accommodate the passage of ILI tools.
Besides the typical challenges of designing a new pipeline or modifying an existing one to ensure it meets the code requirements for ILI tool passage, some unexpected issues can occur when operators attempt to construct new lines or modify them to be piggable. In particular, selection of small-diameter piping (14" and below) and fittings can meet design standards, but still be completely unpiggable resulting in new pipeline construction that is less or not piggable at all. Several real-world situations are discussed where good intentions to increase piggability have backfired, including pipelines that are designed with restricted bores, pipelines that are constructed of materials that due to the manufacturing process have unexpected bore restrictions, and pipelines that have bore restrictions due to the construction process.
Guanlan Liu1, Dan Rowe2
1DNV, Dublin, USA. 2NiSource, Fort Wayne, USA
Pipelines play a critical role in transporting fluids, and the assessment and mitigation of associated risks are paramount. Over the past decades, pipeline risk models have evolved from empirical, index-based approaches to more quantitative, data-driven models, providing insightful results for operators to make decisions regarding inspection, mitigation, repair, or replacement efforts. However, data uncertainty and limited data availability have consistently posed challenges in quantitative or probabilistic risk assessment models. Therefore, efficiently improving data quality and completeness becomes necessary, which requires a judicious decision on allocating limited resources for data collection efforts. To meet this goal, a sensitivity assessment on pipeline risk models becomes critical.
This research focuses on identifying and understanding the sensitivity of crucial input factors spanning from pipeline specifications to environmental conditions. A data-driven probabilistic risk assessment model was selected, and the baseline parameters were set up based on a selected pipeline. By systematically varying the model parameters in a reasonable range, and observing their impact on the likelihood of failure, the study aims to prioritize factors significantly influencing the likelihood of failure. After determining the range of the selected factors, a Monte Carlo simulation up to a million iterations was conducted with random sampling inside the defined distribution, and the correlation coefficients between these factors and the risk results were analyzed. As a result, a ranking of the criticality of these factors is summarized. Additionally, a threat-based sensitivity analysis was conducted, specifically on pipeline threats such as corrosion, mechanical damage, incorrect operation, etc., to evaluate which factor affects the likelihood of a specific threat more.
The results contribute to informed decision-making and resource allocation for risk mitigation strategies. Additionally, the research emphasizes the importance of iterative sensitivity analyses, considering uncertainties, and continuous refinement of the risk assessment model to enhance its accuracy and relevance in dynamic operational environments. The findings of this study offer valuable insights for stakeholders involved in pipeline management, safety, and regulatory compliance.
Nathan Leslie1, Jake Haase2, Jonas Butterer3
1NDT Global, Houston, USA. 2Colonial Pipeline Company, Alpharetta, USA. 3NDT Global, Stutensee, Germany
Ultrasonic Inline Inspections (ILI) have been extensively utilized by liquid pipeline operators for many years, facilitating the accurate detection, sizing, and characterization of pipeline features. Over the past two decades, significant investments in the innovation of ultrasonic ILI tools have resulted in higher data fidelity, advanced analysis techniques, and increased detection and measurement capability. However, these advancements have also led to an increase in the length of ILI tools. While many pipeline operators can accommodate the extended tool length in order to leverage these advancements, trap extensions were not a realistic option for Colonial Pipeline. To benefit from these advancements in their Integrity Management Program, Colonial Pipeline required a novel solution that could provide high-quality ultrasonic crack and metal loss inspection data without exceeding the dimensions of their existing tray-style launching and receiving traps.
This paper explores the development, testing, qualification, and application of a 36-inch combination crack and metal loss detection tool, developed in collaboration with Colonial Pipeline. The new design not only meets the compact length requirement but also offers enhanced field reconfigurability, allowing it to adapt to a wide range of pipeline diameters (30" to 40") and easily deploy multiple crack detection technologies. Engineers from both organizations collaborated from the initial problem statement and preliminary designs through to the assembly, testing, and qualification of the ILI tool. This paper addresses the unique challenges during the project. This case study illustrates how ILI service providers and pipeline operators can work together to continuously adapt emerging ILI technology to the benefit of pipeline safety.
KEYWORDS: Ultrasonic ILI; UT Crack Detection; UT Metal Loss; Combination ILI; Operator / ILI Provider Collaboration
Alan Morton, Jim Kay, Dick Williamson
R.B. Williamson Energy Advisors, Tulsa, USA
Pressurized hydrocarbon is a formidable entity. While pipeline operators and service providers have developed safe and accepted procedures for managing it, some threats may be dynamic and require efforts beyond the checklist.
For example, the safe management of pressure and vapors during the launching and receiving of cleaning pigs and inspection tools requires continuous monitoring and mitigation. That includes knowing how to manage hydrocarbon, oxygen and ignition sources to keep field personnel safe and assessing the integrity of the pig trap assembly and its components to ensure they can hold pressure and operate as expected.
Over time, a phenomenon known as normalization of deviation has allowed field practices, culture and tribal knowledge to become the standard for a given process. Understanding the threats that drove the establishment of safe pig trap procedures will help bring awareness to field practices that may deviate from the approved practices.
The purpose of the paper is to show how products and processes for the operation of launchers and receivers have evolved over time based on feedback from the field. This paper will discuss pressure management with the trap, management of gases and liquids within the trap, managing potential ignition sources, ensuring trap integrity and safety practices for traps, components and closures under both normal and abnormal operating conditions.
Key words: normalization of deviation, traps, tribal knowledge, safety, launcher, receiver, threats, hazards
Paul Chittenden
TSC Subsea, Houston, USA
Ensuring the integrity of pipeline systems is critical for optimizing operational efficiency, minimizing environmental impact, and safeguarding personnel and public safety. Neglecting pipeline maintenance can lead to reduced production and, in worst cases, catastrophic failures due to undetected cracks or corrosion.
Traditionally, pipeline operators rely on in-line inspection (ILI) pigging solutions, which require specific pig launching and receiving facilities. When such facilities are unavailable, pipelines are often deemed non-piggable or challenging to inspect. In these cases, external surface inspection becomes the alternative, although this approach is not always feasible due to pipeline material or external obstructions.
This presentation introduces two case studies that showcase the evolution of a new crawler-based inspection delivery method. This method enables spot inspections using remotely operated scanning technologies, and represents the next step towards full integration with ILI scanner systems for comprehensive pipeline inspection.
The first case study involves an internal corrosion and crack assessment on a 14-inch duplex riser located on an offshore platform in the North Sea. Initially installed as a spare, this 110-meter riser, with recessed welds every 10 meters and three complex 3D bends, had never been operational. The client required definitive assurance of its integrity before commissioning the riser for an upcoming development project. The riser, filled with anti-corrosion fluid at elevated temperatures, presented significant inspection challenges due to its single entry and exit point.
To address these challenges, a robotic bidirectional tethered crawler was deployed, capable of navigating through the riser, precisely stopping, stabilizing, and performing detailed corrosion and crack assessments as required.
Advanced NDT technologies were crucial for this complex inspection. The methods employed included Alternating Current Field Measurement (ACFM) for detecting surface-breaking cracks in recessed welds and Subsea Phased Array (SPA) for volumetric weld inspection and corrosion detection and mapping.
The inspection was successfully completed, allowing the client to proceed with their development project and re-commission the riser. The tethered ILI solution played a pivotal role in enabling the client to return the riser to service and meet project timelines.
A major engineering challenge involved designing the delivery vehicle to navigate vertical pipe sections with multiple bends and to precisely stop at areas of interest. The vehicle was also required to rotate 360 degrees while maintaining consistent probe pressure on the inspection surface.
Following the successful delivery system design, the next phase involves full integration with an ART Scan module to assess wall thickness for two 4,000 ft. long non-piggable pipelines. This paper will further explore the development process and the upcoming field trial, scheduled for completion by the end of 2024.
Samarth Tandon, Sergio Limon, Ravi Krishnamurthy, Shaikh Rahman
Blade Energy Partners, Houston, USA
Accurately predicting limiting pressures in fitness-for-service evaluations is crucial for maintaining pipeline integrity, determining necessary mitigations, and scheduling the next assessment intervals. While API 579-1/ASME FFS-1 FAD Level 2 has been used in the past for fitness for service determination of limiting pressure predictions, its conservatism has not been thoroughly quantified for pipelines with cracking and seam weld defects. This lack of quantification has led operators to apply additional safety factors, resulting in overly conservative limiting pressure predictions. This paper estimates the inherent conservatism of API-579 FAD Level 2 with respect to pipeline rupture failures by analyzing results from the burst testing, in-service, and pressure test failures of pipelines with natural Stress Corrosion Cracking and Toe Weld Cracks. Implications of the findings are discussed.
Rhett Dotson1, Ryan Sager2, Brian Leis3, Morry Bankehsaz2, Jonathan Hardy4
1D2 Integrity, Houston, USA. 2ROSEN, Houston, USA. 3B N Leis, Columbus, USA. 4TD Williamson, Salt Lake City, USA
The shape parameter methods used to define the severity of a dent developed as part of research efforts within PRCI have been the subject of significant debate within the pipeline industry. Publications as early as 2019 began identifying challenges in applying the methods outlined in PRCI Reports. Since that time, the shape parameter methods have been updated and incorporated into the 2021 edition of API recommended practice (RP) 1183. Following their inclusion in RP 1183, several publications identified technical questions surrounding the methods and example problems included within the RP. Additionally, many operators have begun incorporating the methods into their integrity management plans. In response, ILI vendors and consultants have sought to automate the process for extracting the required information from dent profiles captured by ILI tools. This paper examines some of the key challenges in automating the process of characterizing dents and extracting the necessary information for the shape parameter methods which have not been broadly discussed within the industry to date. In particular, the paper examines the challenges in identifying complex dents, establishing depth baselines, repeatability, and employing smoothing. Additionally, the paper examines some questionable behavior in the recently released updates to the equations. The paper concludes with recommendations for operators and vendors using the method and potential questions that should be addressed in future industry research.
Joel Van Hove1, Owen Bunce2, Casey Dowling3, Pete Barlow4
1BGC Engineering, Vancouver, Canada. 2BGC Engineering, Calgary, Canada. 3BGC Engineering, Golden, USA. 4BGC Engineering, Edmonton, Canada
Horizontal directional drilling (HDD) is a widely used trenchless technology for pipeline installations, especially in areas where conventional open trench construction poses significant construction challenges, such as river or landslide crossings – areas which also present geohazard risks. HDD installations can be highly effective at avoiding and nearly eliminating geohazard risk, but the failure records from industry reveal that many HDDs fail to effectively avoid landslides and some significantly increase geohazard risk. A recent study of North American pipeline systems estimated that HDD installations have been used at approximately 14% of landslide crossings, and at 16% of those crossings, the pipeline is drilled through, rather than below the landslide. The same study reviewed an extensive history of geohazard related pipeline failures and found a 15 times greater failure rate for pipelines intersected by active moving landslides where the installation method was HDD versus conventional trenching. This observation means that pipelines installed by HDD, which do not effectively avoid landslides, are at a much higher risk of failure and represent the category of geohazards most likely to cause pipeline failure.
Considering the elevated risk HDD crossings of landslides represent, assessing the effectiveness of each crossing is critical to successful geohazard risk management. Existing methods of landslide assessment such as visual inspections from landslide experts, survey monitoring, and lidar change detection often fall short in evaluating the depth and activity of a landslide, which is crucial for understanding the risk to HDDs. While installing deep instrumentation like slope inclinometers can provide the necessary data, it is costly, time-consuming and prohibitive for wide scale application.
Inertial Measurement Unit (IMU) bending strain analysis has become a critical tool for HDD effectiveness assessment because the data is widely available, precise, and provides the opportunity to directly observe landslide impact to a pipeline by transforming the pipeline itself into an instrument to detect bending strain, much like a slope inclinometer. This paper compiles findings from bending strain analysis across hundreds of HDDs, detailing characteristic strain patterns and cataloging examples where landslide impact was identified and confirmed. The distinct bending strain patterns caused by landslide movements can be detected at low strain levels, often below typical reportable limits for bending strain analysis, due to the unique and low strain magnitude signatures typical of HDD installation.
Recognizing these strain signatures and interpreting them in the context of potential landslide loads allows early identification of landslide impact and provides operators the opportunity to proactively manage risk and avoid ruptures and service outages. Since HDDs represent a disproportionate amount of geohazard risk, assessing HDDs for landslide impact is one of the highest value actions operators can take to manage geohazard risk. IMU bending strain analysis proves to be an effective tool for this purpose, offering a practical method for detecting and assessing landslide impacts on HDD pipelines.
Russell Giudici1, Travis Greenstreet2, Chris Alexander2
1Advanced FRP Systems, Inc., Weymouth, USA. 2ADV Integrity, Magnolia, USA
Pipelines that operate at elevated temperatures present unique challenges to composite repair applications. The material performance of a composite repair is impacted both by its cure temperature and the operating temperature. These variations collectively influence the pressure capacity of the applied composite system.
The first question explored in this paper is the degree to which the properties of a composite system, specifically the tensile strength and modulus, change at various elevated temperatures compared to ambient temperatures. The second question explored in this paper is how the cure temperature of the composite affects the tensile strength and modulus at various temperatures. An elevated temperature post-cure will increase the crosslink density of the polymer, which should result in a stronger, stiffer cured material. Increased crosslink density will also likely affect the elevated temperature properties of the composite repair system.
The testing program referenced in this paper developed a protocol to evaluate the abovementioned questions. Two commercially available, carbon fiber-based composite repair systems were tested. Each system was tested for tensile strength and modulus at various temperatures, from 70oF – 250oF. All samples were analyzed based on tensile strength, yield strength, glass transition temperature (Tg), and ductility on a stress/strain curve. The full test protocol was performed on both composite repair systems at three different cure temperatures. Ultimately, the intent of this testing program was to evaluate how the properties of composite repair systems change at elevated temperatures and to explore how variations in a composite’s cure temperature affect these properties.
Alan Morton, Larry Alspaugh, Dick Williamson
R.B. Williamson Energy Advisors, Tulsa, USA
The use of in-line inspection (ILI) tools and cleaning pigs is a common and successful way to manage the ongoing integrity of operational pipelines.
However, even with thorough planning, in some instances these tools and pigs can become damaged or, worse still, lodged in the pipeline. A lodged tool can disrupt flow and recovering it may result in the suspension of normal operations.
Conditions that can contribute to a failed pig run include excess debris in the pipeline; unknown pipeline bends or wall thicknesses; intrusive equipment, such as pig signalers, corrosion coupons or sensing equipment not addressed prior to the run; improper management of pumps and compressors, the style of the pig or inspection tool; and incompatible valves or fittings.
The options for mitigating a lodged tool or pig are just as unique as the interactions between the pig, the physical pipeline and the operating conditions and depend upon whether the pig is truly stuck in place or has just stopped or stalled. They include temporarily increasing pressure to the pig’s drive cups, surging the line —which involves rapidly closing then opening a valve to send short bursts of pressure to help dislodge the pig — reversing flow or using a recovery tool to push the ILI tool to the receiver.
If all other measures fail, the tool must be removed from the line by a cutout project. This involves accurately locating the tool inside the pipeline, isolating the affected pipeline section, cutting into the pipeline, retrieving the lodged tool and repairing the pipeline.
This paper will review the reasons a tool or pig can stop in a flowing pipeline, discuss how tool and pipeline conditions affect run success and provide guidance into planning a successful run. It will also describe the mitigation steps involved in locating a lodged tool, including using pipeline and tool data to evaluate why the tool stopped and evaluating the options to safely get the tool moving again. This paper will also explain the processes for retrieving the tool or pig, incorporating lessons from fields around the world.
Key words – pig, recovery, tracking, flow management, integrity, abnormal operating condition, ILI tool, launcher, receiver, trap
Christopher Newton1, Jordi Aymerich2, Sayan Pipatpan3, Tannia Haro4, Santiago Urrea3, Alex Hensley4
1Phillips66, Houston, USA. 2NDT Global, Calgary, Canada. 3NDT Global, Stutensee, Germany. 4NDT Global, Houston, USA
Pipeline operators rely on a variety of strategies to maintain the safety and integrity of their pipeline systems, with inline Inspection (ILI) and Non-destructive Examination (NDE) being crucial components. However, these methods can encounter challenges and limitations when identifying and sizing complex features, such as off-axis cracking. What happens when NDE evidence suggests a systematic measurement bias relative to ILI? Can operators still use this data within their Integrity Management Programs (IMP)? Moreover, can this NDE data be effectively leveraged to develop new rules for ILI analysis processes?
Last year, NDT Global, in collaboration with Phillips 66, developed a Phase I systematic method to identify crack complexity in previously detected and undersized features based on NDE campaign results. This novel methodology integrated years of accumulated knowledge from ILI survey data from various pipelines with insights from applying sophisticated in-ditch NDE techniques developed for complex features.
In Phase II, as discussed in this paper, the investigation advances further by validating the Phase I methodology using destructive lab testing results. The metallurgical evaluation includes nine ILI-reported linear anomalies that were previously examined non-destructively in a 6" pipeline. The destructive testing aims to determine whether NDE accurately identified and sized these anomalies and whether the original ILI results were biased in the first instance. Additionally, this phase explores methods to assess the Probability of Sizing (POS) for out-of-specification features and suggests potential adjustments to ILI tool sizing curves when truth data is available.
This study highlights the successful partnership between NDT Global and Phillips 66 in advancing pipeline integrity management, offering valuable insights for the future of pipeline safety and reliability.
KEYWORD(S) FOR SUBJECT AREA
ILI verification, validation; ILI analysis; Crack assessment and management
Thomas Hennig, Michael Haas, Katja Traeumner
NDT Global GmbH, Stutensee, Germany
Gas transmission lines, especially those constructed between the mid 20th century and early 1980s are often affected by external stress corrosion cracking (SCC). Traditionally, Operators have used Electromagnet Acoustic Transducer (EMAT) based inline inspection tools to detect and characterize these flaws, ensuring the integrity of the asset.
However, EMAT technology is not only sensitive to SCC or other types of cracking, but it also delivers a high incidence of false positives, posing significant operational challenges. To overcome this, a circumferential magnetic flux leakage tool (MFL) is used in addition to the EMAT inspection enhancing the accuracy of crack identification and characterization.
To enhance and refine crack inspection of gas pipelines and reduce the risk of unnecessary digs, NDT Global has developed CIGMA- x an advanced technology for crack detection, identification, and sizing. based on directional gas-coupled guided wave generation in the pipe wall, CIGMA-x allows us to inspect an asset without any contact of the sensors to the internal pipe wall.
The small size (compared to EMAT) of the sensors allows for a high sensor density, delivering high resolution and accurate data which ensures detection, identification and sizing of SCCs and other types of cracking.
The authors will present the outcomes of an industry-funded development project, including the results of small-scale laboratory testing and full-scale evaluations conducted in a nitrogen-filled pressure chamber on 20" and 30" pipeline sections. Additionally, the paper will discuss the optimization of sensor designs tailored to varying pipeline wall thicknesses, as well as insights into the data analysis methodology and the necessary infrastructure for implementing this cutting-edge technology.
Henning Bø1, Thomas Bergsland2
1T.D. Williamson, Stavanger, Norway. 2T.D. Williamson, Houston, USA
In the complex and demanding environments of subsea and offshore pipeline operations, ensuring the safety and integrity of critical infrastructure is paramount. The ability to precisely control and monitor non-intrusive isolation tools is essential, particularly during valve repair or replacement on offshore platforms, where depressurization of the entire pipeline can be costly and environmentally detrimental.
This paper explores the innovative combination of non-intrusive isolation tools with a tetherless two-way communication system, which allows for remote activation, isolation, and monitoring of pipeline isolations. By utilizing extremely low-frequency electromagnetic signals, this system enables precise two-way communication through pipeline walls up to 65 mm (2.56 inches) thick, a feature especially valuable in subsea or buried applications where physical access is limited. The remote communication capability allows operators to monitor key parameters such as annulus pressure, pipeline temperature, and the integrity of isolation barriers in real time, ensuring that the isolation is maintained without compromising safety or operational efficiency.
Furthermore, this integration provides significant advantages during valve replacement operations, where localized pipeline isolation can minimize production downtime and loss of product through flaring or venting of the pipeline, thereby reducing environmental impact and associated costs. The paper will present case studies, including a four-year isolation project in the Tyra field of the North Sea, where the integrated system was used to remotely monitor and control the isolation without any degradation in seal integrity. The combination of non-intrusive double block and monitor technology with advanced communication systems offers a robust solution that satisfies both regulatory requirements and operator concerns, enhancing the safety, reliability, and efficiency of pipeline operations.
KEYWORD(S) FOR SUBJECT AREA : Tracking and Locating, Isolating/Plugging, Pig Signalers, Non-intrusive isolation
Greer Simpson1, Corey Richards1, Carlos Costa1, Aaron Schwing2, Jeremy K Holifield2, Jason M Moritz2
1DarkVision Technologies, North Vancouver, Canada. 2Flint Hills Resources, Wichita, USA
Pipeline operators are gaining significantly more intuitive results with a novel In-line Inspection tool that comprehensively evaluates every major anomaly type – metal loss, axial cracks, and dents – in a single run. This technology represents a fundamental improvement in resolution and the ability to understand combined threats impacting pipelines. Direct 3D measurements reveal the shape and orientation of anomalies that enable operators to better understand the root cause and context of the anomaly. This direct imaging method is not only more intuitive for industry, but it also overcomes legacy amplitude-based inferred measurement methods that have limitations when measuring crack morphologies.
The tool leverages the latest developments from phased array in-ditch based handheld systems, medical imaging, and upstream oil and gas ultrasound imaging technologies to bring ultrafast imaging rates with 0.5mm axial resolution, and 0.25mm circumferential resolution at line speeds exceeding 3 meters/second. Over 6,000 independent sensors mounted on encoded carriers detect and size metal loss, axial cracks, and dent information from a single registered pass.
This paper presents and validates the technology in accordance with API 1163. A 400-meter continuous flow loop was engineered and constructed to test the tool’s endurance and validate the tool’s performance over a variety of anomalies including electrical discharge machined (EDM) notches, manufactured cracks, and wall loss. These results are validated against industry standard tools including a metrology-grade laser scanner and a phased-array ultrasound handheld tool. Additionally, the results related to identification and measurement of challenging anomalies such as stress corrosion cracking (SCC), hook cracks and lack of fusion that were removed from Flint Hills Resources pipelines are presented. Lastly, findings from a full-scale deployment in a segment of Flint Hills Resources 16" transmission pipeline are summarized.
Tom Alexander1, Benjamin Mittelstadt, P.E.2, Stephen Barnet2, Peter Seydewitz3
1Dynamic Risk, Toronto, Canada. 2Dynamic Risk, Houston, USA. 3Enbridge Gas Transmission, Houston, USA
The integrity of pipeline systems relies heavily on the accuracy and completeness of records that are Traceable, Verifiable, and Complete (TVC). As regulatory scrutiny increases, the need for reliable validation methods becomes of paramount importance. This study focuses on leveraging In-Line Inspection (ILI) data to enhance the validation of existing records, ensuring that operators can confidently manage pipeline integrity and meet regulatory requirements.
TVC records play a key role in pipeline integrity and operations, including tasks such as Maximum Allowable Operating Pressure reconfirmation (MAOP-R) through Engineering Critical Assessment (ECA), quantitative risk assessments (QRA), and establishing accurate class locations. These records will also be important for the potential application of the proposed methods under 192.618.
TVC records form the foundation for all analysis and conclusions and will be a primary focus during regulatory audits. Recent experience has highlighted the potential for gaps, particularly where TVC status was established prior to recent amendments under 49 CFR 192. The pipeline industry has invested significant time and effort in establishing TVC records and duplication of that effort is unnecessary, however understanding and resolving remaining data issues (i.e. TVC the TVC) is required. Manually addressing such issues would be a complex and labor-intensive process involving extensive data review and verification, however, ILI technology offers a powerful and efficient way to confirm confidence in records that may be considered vital in establishing the integrity and safety of the pipeline system.
Recently emerging Material identification ILI technologies offer valuable insights or the confirmation of material properties. The value of ILI data for material identification is however not limited to such advanced technologies. Conventional ILI dimensional information such as joint lengths, wall thickness changes, and other attributes are visible in diagnostic ILI technology data. When these data points, are correlated with existing records, they can significantly streamline the validation process, reducing the burden of manual verification and enhancing the reliability of TVC records. This approach not only ensures compliance with current and proposed regulations but also supports the integrity and reliability of pipeline operations.
Integrating ILI data with Geographic Information System (GIS) data and historical TVC records can significantly enhance confidence in the accuracy and completeness of TVC records, as well as in the GIS data’s ability to accurately represent the materials in the pipeline. This approach involves a detailed analysis of ILI data to identify discrepancies and gaps in the existing GIS data and records, thereby providing a solid foundation for regulatory compliance and effective risk management.
Shree Krishna, Udayasankar Arumugam, Ryan Milligan, Ravi Krishnamurthy
Blade Energy Partners, Houston, USA
This paper introduces a methodology aimed at analyzing failures in buried pipelines exposed to significant geotechnical displacement. The occurrence of ground movement and heave generates substantial longitudinal strain through elongation and bending, potentially leading to buckling in the pipeline segment. Buckling, in turn, can compromise the pipeline’s elastic stability, allowing further elongation with soil movement. The girth weld’s presence acts as a potential weak point, susceptible to either brittle or ductile failure. Conventional analyses using standards such as ASME B31.8 or API 1104 tend to provide conservative estimations and often fail to fully elucidate the extent of geotechnical displacement or the root cause of failures. Moreover, these approaches overlook addressing failures that may occur when the girth welds are ductile in nature as specified in API 1104. This is especially true for modern steels.
To effectively tackle extensive geotechnical displacement, this paper advocates for strain-based damage methodologies utilizing critical strain as a pivotal material parameter. Understanding the true stress-strain behavior, particularly the critical strain parameter of base metal, Heat Affected Zone (HAZ), and weld, is crucial in predicting potential failure. The paper’s approach involves reviewing existing strain-based failure methodologies in literature and then delving into analyzing the geotechnical movement of buried pipeline segments using a critical strain-based failure criterion. The pipeline’s lateral displacement is analyzed through a finite element approach that integrates global and detailed local sub-modeling. This examination includes showcasing the impact of weld misorientation and the presence of planar defects related to welding. The paper also discusses the evolution of damage at the local girth weld, emphasizing the significance of the “Ductile Failure Damage Indicator (DFDI)” parameter. Finally, a series of finite element analyses illustrate the loss of elastic stability due to buckling in pipes subjected to pure bending and internal pressure. It concludes by outlining the limitations of other geohazard fitness-for-purpose approaches relying on parameters like CTOD (Crack Tip Opening Displacement) and demonstrates the successful application of the methodology in analyzing a buried pipeline failure.
Pooya Delshad1, Peter Martin2, Emily Brady3, Jeffrey Kornuta3, Jonathan Gibbs1, Peter Veloo1
1Pacific Gas and Electric Company, San Ramon, USA. 2RSI Pipeline Solutions, New Albany, USA. 3Exponent, Houston, USA
Instrumented Indentation Testing (IIT) is a non-destructive technique used to estimate mechanical properties such as yield strength and ultimate tensile strength of materials, making it a useful tool in the assessment of pipeline steels. Although the importance of surface preparation for accurate IIT measurements is widely recognized, published systematic studies evaluating the specific effects of varying surface finishes on IIT results are rare. Identifying the potential implications of over- or under-preparation could help ensure more efficient and accurate IIT.
In this study, the impact of different surface finishes, ranging from 280 grit to 2000 grit, on the yield strength measurements of pipeline steel using IIT was investigated. Various locations on the pipe were ground and polished to these target surface finishes, and IIT was performed at each location. Metallographic cross-sections were prepared from the locations of different surface finishes with IIT indents to analyze the influence of surface preparation.
Preliminary results indicate that IIT measurements taken at a 1200 grit surface finish are more consistent with the yield strength values obtained from destructive transverse tensile tests. In contrast, IIT results at 280 grit exhibited yield strength values significantly higher than those from tensile testing, while measurements at 2000 grit showed lower yield strength values in some cases, which could be attributed to polishing parameters such as the pressure applied during the polishing process and the polishing time. Metallographic analysis suggests that the rough surface at 280 grit and the formation of surface voids at 2000 grit may have contributed to these discrepancies.
This ongoing experimental work aims to establish a conclusive understanding of the relationship between surface finish and IIT measurements, potentially identifying an optimal surface preparation technique that ensures reliable IIT data without unnecessary refinement efforts.
KEYWORDS: IIT, Surface Preparation, Polishing, Yield Strength, Material Properties Verification
Travers Schwarz1, Steven Kinikin1, James Fetherolf1, Davie Peguero2, Jackson Herrod2
1Sacramento Municipal Utility District, Sacramento, USA. 2Henkel Corporation, Riviera Beach, USA
Pipeline operators continue to rely on acceptable methods of repair outlined in ASME B31.8S when making decisions to repair their pipeline in the field. The damage is most often attributed to one of the nine defined threat categories listed in B31.8S: External Corrosion, Internal Corrosion, Stress Corrosion Cracking (SCC), Manufacturing defects, Welding/Fabrication defects, Equipment defects, Third-Party Damage, Incorrect Operations and Weather or Outside Force. Although not all pipeline damage can be repaired, options are available and can be utilized by the operator to mitigate the threat and keep the pipeline in operation.
Sacramento Municipal Utility District (SMUD) encountered a recent incident where third-party damage occurred on a section of their gas transmission pipeline system; located inside a High Consequence Area (HCA). The pipe damage was caused by an unmarked bore crossing, gouging the top of pipe near the girth weld and long seam weld. Decision was made to use an engineered, approved carbon fiber composite wrap to repair the pipe; this ensured the pipe maintained its full-strength integrity while allowing the operator time to plan, and schedule resources for the replacement of the damaged section of pipe.
SMUD worked with the composite manufacturer and performed a cyclic pressure test, a hydrostatic burst test and an adhesion test on the damaged segment of pipe. This paper looks at the design characteristics of the carbon fiber composite wrap which was tailored for this specific type of repair in accordance with ASME-PCC-2 standard, and the actual findings when the repair underwent a stressed condition. The expected results intend to provide operators with better insight and confidence when using this repair method on their pipeline systems in the future.
Zahra Lotfian1, Michiel Brongers2
1Kiefner and Associates, Houston, USA. 2Kiefner and Associates, Columbus, USA
While pressure cycle fatigue may not typically be a significant concern in conventional gas pipelines, introducing hydrogen changes the dynamic. This makes pressure cycle fatigue analysis a critical factor in ensuring mechanical integrity. Hydrogen can significantly alter material properties through embrittlement, accelerating crack growth rates. As the industry shifts towards hydrogen blending in natural gas pipelines, accurate remaining life assessments become essential for effective integrity management. This is especially true for small flaw sizes that may not be detectable by ILI or other NDE tools.
As part of ongoing research for the United States Department of Transportation (USDOT) Pipeline and Hazardous Materials Safety Administration (PHMSA), this paper addresses the challenge of assessing flaws just below the detection limits of ILI and NDE tools. Through a series of case studies, the remaining life of these subcritical flaws is estimated, considering variables such as flaw size, location (e.g., pipe body, seam weld), pipeline grade, and the severity of pressure cycles. Unlike the traditional Paris Law approach commonly used for Region II (stable crack growth) fatigue analysis, this study employs advanced models to capture a broader range of material behaviors, including Region I (threshold) and Region III (rapid crack growth), while also accounting for pressure cycle severities. Experimental data is directly incorporated into fatigue crack growth calculations to further reduce conservatism instead of relying on standard fatigue design curves.
Operators will gain insights into how hydrogen exposure impacts pipeline remaining life and can use this knowledge to make informed decisions for setting reinspection intervals and extending the operational life of pipelines in hydrogen environments. While the findings provide important guidance, they also emphasize the need for ongoing research and thorough technical assessments.
KEYWORDS: Pipeline, Hydrogen, Fatigue, Remaining life, Crack, ILI, NDE, PHMSA
Peter Martin1, Nathan Switzner1, Owen Lopez-Oneal2, Sophia Curiel2, Peter Veloo2
1RSI Pipeline Solutions, New Albany, USA. 2Pacific Gas and Electric, San Ramon, USA
It is widely accepted that the yield strength of low carbon and low alloy steels can be modeled as the sum of contributions from intrinsic lattice friction stress, solid solution strengthening, grain size effects, dispersion strengthening, and dislocation density. Dispersion strengthening can be neglected for hot-rolled steels that aren’t microalloyed with Nb, V, or Ti, while models for solid solution (Pickering), grain size (Hall-Petch), and dislocation density (Taylor) effects have been extensively validated in published research dating back as far as the 1930s. These models have been shown to be accurate and effective, but line pipe applications have been limited because the quantitative metallography required to determine grain size has historically been time consuming and resource intensive. The recent development of a machine learning model to perform rapid, reliable grain size measurements warrants revisiting these models.
In the current work, the yield strengths for a set of 39 hot-rolled, non-microalloyed steels are estimated from the %Mn, %Si, %Cr, %Cu, and grain size using the model published by Pickering in 1978.[1] The model calculates the grain size and solid solution contributions using only the original coefficients published in 1978, while the contribution of dislocation density is estimated by assuming a constant, average dislocation density for all hot rolled, non-microalloyed pipes. Comparison of model predictions to yield strengths from tensile testing resulted in a mean absolute percent error (MAPE) of 8.0% with a 95% prediction interval of ±11.8 ksi. This performance compares favorably to the instrumented indentation test (IIT), where comparison to tensile testing for an expanded set of 83 pipes yields a mean absolute percent error (MAPE) of 8.6% with a 95% prediction interval of ±12.2 ksi. In a direct comparison of 30 pipes for which both sets of data were available, yield strengths estimated by the model and by IIT predicted the results from tensile testing with MAPE values of 8.2% and 6.8%, respectively, and 95% prediction intervals of 12.0 and 12.5 ksi. The results suggest that this model may be a useful tool to confirm strength testing by IIT, provide strength estimates where IIT is not practical, or replace some fraction of strength testing altogether.
[1] Pickering, F.B. Physical Metallurgy and the Design of Steels; Applied Science Publishers: London, UK, 1978; p. 63.
Colin Scott
AP Dynamics, Calgary, Canada
Pipeline operators routinely carry out inline inspections to identify deformation on their pipelines, and specifically dents. Dents represent time dependent failure mechanisms, as the flexing of a dent under pressure cycling conditions can result in crack initiation and fatigue growth. Recently developed dent assessment techniques have exposed various challenges to analysts, with industry finding difficulty in reaching consensus on an optimum methodology (Leis PPIM 2023).
In this work, we review the extensive published industry laboratory data. Various key parameters are investigated, including pipeline diameter and wall thickness, dent depth, pressure cycling magnitude and R-ratio, and restraint conditions. Numerical analyses are used to focus on the key parameters of interest to the remaining life assessments. More importantly, we also highlight the key parameters that do not appear to play a significant role in predictions.
The result of the project is a simplified dent remaining life assessment methodology that focusses on a single key parameter to the assessment. The less-relevant parameters are disregarded, as they bring a complexity to the assessment with no apparent benefit. Preliminary analysis suggests an improvement in model reliability and the possibility of improved program efficiency for operators.
Justin Oliveira, Sunil Chintalapati
Boston Geospatial, Boston, USA
Energy infrastructure is exposed to an active and ever-changing geohazard landscape, and regulators are raising the bar for operators to better quantify, prepare for, and mitigate potential impacts from these threats. On June 2, 2022, PHMSA released its updated advisory bulletin reminding owners and operators about the seriousness of geohazards. In this update they highlight various case studies involving failures due to or likely due to subsidence, landslides, seismicity, and more. Furthermore, the bulletin offers various suggestions for abatement including ILI surveys, in situ sensors, remote sensing, geotechnical surveying, and more. Because these hazards are so diverse, no one technology can adequately address them. Instead, a concert of solutions must be combined together to ensure pipeline integrity and achieve the desired performance. This paper will explore case studies referenced in the bulletin using a GIS-based geohazard tool funded in part under the PHMSA Pipeline Safety Research and Development Program. The paper will combine terrestrial, airborne, and satellite measurement phenomenologies to explore the case studies and demonstrate the tools use for identifying and measuring geohazard risk and estimating the anticipated mechanical loading.
Syed Aijaz1, Clifford Maier1, Michael Gloven2
1TC Energy, Houston, USA. 2Pipeline-Risk (PLR), Denver, USA
Big data, machine learning and artificial intelligence: these buzzwords invariably create a lot of hype but do they actually live up to it? TC Energy’s threat management team set out to answer that question by curating a comprehensive dataset of pipeline integrity digs in-ditch findings to create a machine learning model for predicting SCC on its transmission pipeline assets. In collaboration with Pipeline-Risk (PLR), results from 1800+ digs since 2012 containing approximately 27,000 data points were consolidated. A classification-based machine learning model was trained on a subset of the consolidated dig data, and its performance was then evaluated using the remaining, unseen portion of the dataset. The results exhibited an impressive predictive efficacy of up to 90% for predicting likelihood of SCC on TCE transmission pipelines. This model is now utilized in assisting in SCCDA dig site selection workflows and prioritizing ILI assessments resulting in significant efficiency gains. The most important factors contributing to the success of this model were a robust, and highly organized enterprise data infrastructure, SME-driven criteria and an effective team structure allowing a comprehensive threat management approach. This paper will present key data strategies to ensure your organization is optimally positioned with people and processes to maximize value created by the computational prowess of machine learning.
KEYWORDS: SCC Threat Management, Machine Learning
Ryan Holloman1, Lyndon Lamborn2, Greg Thorwald1, Michael Turnquist1
1Quest Integrity, Boulder, USA. 2Lamborn Engineering, Inc, Edmonton, Canada
This paper summarizes a study in which Quest Integrity and Enbridge investigated the impact of grinding repair on the stability of axial and circumferential cracks as the griding is taking place. This study was conducted in response to a 2017 PRCI project that experimentally investigated grind repairs on axial cracks manufactured on the surface of vintage pipeline material. The 2017 PRCI project aimed to demonstrate that a reduction in stress intensity would take place during the grinding process. However, these experiments captured an apparent decrease in remaining strength after partial grinding of the crack had occurred.
Interpretation of the data from the 2017 PRCI project was challenging due to the limited number of experimental tests, thus inhibiting statistical relevance. The study presented in this paper utilized elastic-plastic finite element analysis (FEA) to replicate the experimental tests and determine whether there is any theoretical basis to explain a reduction in stress intensity after partial grinding of the crack had occurred.
The same geometry and material values were applied to the models for direct comparison to the experiments. Because FEA is less cumbersome than full-scale testing, more fidelity was added to the existing experimental data points. The grind depths were analyzed in increments of 1/10 of the full-grind depth until the crack was fully removed from the pipe geometry, resulting in a region of metal loss where the crack was previously located. The FEA study was then extended to investigate circumferential cracks subject to both load-controlled and displacement-controlled loading conditions.
The simulations of the axial crack grinding showed a gradual increase in burst capacity, which contradicts the 2017 PRCI study. Based on the results presented in this paper, the decreased experimental burst capacity was likely due to experimental variability from using different vintage pipe spools for individual tests. The circumferential crack analyses also demonstrated no obvious reduction in remaining strength as the grinding took place. The results provide computational proof that the common practice of grinding axial and circumferential cracks is not expected to cause any decrease in remaining strength as the repair takes place.
Noel Nelson1, Pete Weber2, Soek-Bong Lee3, Tim Ross4
1DoC Mapping, San Diego, USA. 2DoC Mapping, New Orleans, USA. 3Doc Mapping, New Orleans, USA. 4DoC Mapping, Calgary, Canada
This paper presents a new and state-of-the-art approach to 3D scour and flood modelling specifically for pipeline water crossings, with a particular focus on simulating and analyzing the effects of record flood events and their effects on potential pipeline exposure and free-span lengths. The technique is major improvement over existing 2D analysis techniques looking at a cross section directly above a pipeline water crossing.
Pipelines traversing water bodies are susceptible to scour, which can result in structural damage and significant economic losses not just from damage to the pipeline but from premature shutdown of the pipeline due to conservative desktop scour modelling. Our research integrates cutting-edge computational fluid dynamics (CFD) techniques and advanced sediment transport modeling, combined with high-resolution bathymetric and topographic field inspection data to provide a comprehensive assessment of scour and span potential in pipeline water crossings under a variety of statistical flood recurrence intervals.
We introduce a novel 3D scour modeling methodology that considers the complex interaction between water flow, sediment transport, pipeline geometry and depth of cover. This approach leverages high-resolution bathymetric and LiDAR data sets, hydraulic parameters, and sediment properties to accurately predict the scour depths and patterns during various flow conditions. Furthermore, the study explores the extreme scenarios by simulating record flood events, which are essential for assessing the pipeline’s resilience and safety under extreme hydraulic conditions. The outcomes of these simulations are presented in interactive 3D models and offer invaluable insights for optimizing pipeline design, maintenance, and risk mitigation strategies, ensuring the long-term integrity and reliability of pipeline infrastructure in challenging water crossing environments. This research contributes to the advancement of pipeline engineering practices, with the potential to enhance the safety and sustainability of critical waterborne transportation systems.
Robert Smyth
PetroSleeve, Nisku, Canada
A joint industry project including both industry and government, organized by C-FER, has been undertaken to determine if a non-welded repair technology can be used to repair circumferential defects.
With the development of advanced internal inspection tools, industry is now capable of locating circumferential cracking. Obviously, having developed the ability to locate cracking, industry is required to return the integrity of the defect joint back to its’ original level.
Repair methods currently available include removing the affected pipe section (cut out) or installing a welded steel sleeve around the defect (Type B sleeve). The first case is extremely costly, and the second case introduces additional concerns considering the in-service weld.
Consequently, this JIP was instigated to determine whether a non-intrusive repair such as a wet lay-up, composite fabric, preformed composite coil, steel sleeve, or bolt-on repair sleeve/collar could, when installed, prevent the circumferential crack from extending. This project, broken into 4 phases, consists of the evaluation of current non welded technologies and testing those technologies that have promise to repair circumferential cracking.
Phase 1 consisted of Non-destructive tensile testing. This consisted of, after having researched repair types, inviting potential participants (6) identified as Repair A to Repair F to install their repair technology. Each was to install their repair on three sections of 24" pipe pressurized to 785 psi (5400 kPa). In each case, each participant, separately, installed their repair type. There was no information exchanged between the participants, for all Phases.
Following repair installation, the three 24" vessels were pressure cycled and then put under tension to yield of the pipe parent material.
Phase 2 considered the effect of installation pressure. This consisted of having three of the six participants install their repair technology on seven vessels pressurized at 30%, 50%, and 70% of SMYS. The vessels then were pressurized to various levels, put under tension, and then, at 72% SMYS, put under tension until failure.
Phase 3 consisted of destructive tensile testing with a circumferential flaw. In this phase, the repair types were Vendor 1, Vendor 2, and a type B sleeve. In all cases, the repairs were installed at 50% SMYS, initially exposed to pressure cycling, and then setup for the tensile test. At 72% SMYS (1482 psi; 10,200 kPa) the vessels were put under tension until failure occurred.
Phase 4 consists of a long-term performance of repairs test. In this test two participants are involved. The test vessels will be put under tension and load, to simulate field conditions. Phase 4 commenced August 2024, with one of the participants having installed their repair on three 12" vessels pressurized to 1030 psi (7100 kPa) and each containing an 80% circumferential crack.
One of the technologies that was selected for testing was the Steel Compression Reinforcement Sleeve (Repair F) that is participating in Phase 4.
This paper describes the JIP, as it pertains to the Steel Compression technology.
KEY WORDS
circumferential cracking, non-welded repair, testing, repair technologies
Susannah Turner, Fraser Gray, Timothy Turner
Highgrade Associates Ltd, Newcastle upon Tyne, UK
Inspection is used as part of a pipeline integrity management program, to control the risks associated with pipeline failure. Risk based inspection (RBI) methods are commonly used to schedule pipeline inspections. However, the RBI methodologies and approaches which are applied in the pipeline industry are many and varied.
This paper presents and discusses practical application of a pipelines RBI process which provides a direct link between the inspection interval and the risk associated with a loss of containment failure from a pipeline. The RBI methodology considered applies reliability engineering methods to account for the perceived increase in risk over time, due to both degradation-related time-dependent threats and randomly occurring event-driven threats. The presented approach is flexible, allowing detailed, quantified engineering relationships and historical incident rate data to be used where available, with more subjective input from subject matter experts and engineers when required. The uncertainty associated with the assessments is accounted for explicitly, allowing different levels of analysis complexity to be accommodated within the same overall pipeline system RBI study.
The RBI approach schedules inspections such that they are completed before risk reaches a tolerability limit. This ensures that inspections are targeted appropriately to control the risk of pipeline failure. The RBI process also identifies when additional risk mitigation is required to control risk, for example this may be the case if inspection would be required at an impractical frequency, or if no suitable inspection method is available. The assessment process can be further used to investigate the effect on the assessed risk level of changes in the inspection schedule.
This paper builds upon and updates a methodology and process first developed twenty years ago. The study presents an improved development of the methodology and discusses the authors’ experience of practical application and implementation of the RBI process, for large offshore pipeline systems. This practical experience includes elements such as dealing with requirements to combine inspections into optimised campaigns, as well as accounting for the time required to review, assess and act upon inspection findings. The review of experience also considers alignment of the RBI with corporate systems, procedures and risk matrix definitions. The paper concludes by identifying the key elements leading to successful development of an RBI schedule for offshore pipeline systems.
Michael Manahan
MP Machinery and Testing, State College, USA
MPM developed the Instrumented Indentation System (I2S) for measurement of yield stress (YS), ultimate tensile strength (UTS), hardness, and ductility of in-service pipes. The I2S nondestructively indents the pipe surface while measuring applied load/deflection to determine the Brinell hardness. The pipe surface preparation is completed in less than 5 minutes and multiple data points for base, weld, and heat-affected-zones can be acquired in a few minutes. The I2S material model software displays the YS, UTS, and ductility on the portable computer immediately after measurement. The efficacy of the I2S data has been demonstrated by comparison with benchmark laboratory data obtained in the Pipeline Research Council International (PRCI) study and also with the Gas Technology Institute (GTI) benchmark data. For pipes that require plane-strain fracture toughness data, MPM has developed a miniaturized Charpy V-notch (MCVN) impact test that provides Charpy and fracture toughness data from a dynamic test measurement. It will be necessary to trepan small pieces of material (~0.2 inch x~ 0.2 inch x ~1.0 inch long) from the pipe and perform a weld repair as needed. MPM’s test machine is equipped with an instrumented striker for acquisition of the dynamic load and deflection. The advanced mechanics model uses the load/deflection data to determine the material J-resistance (JR) curve and the fracture toughness (JIC and KIC). While it is recognized that other researchers have proposed correlations between Charpy energy (or tensile data) and plane-strain fracture toughness, MPM’s experience shows that these correlations are only valid over limited materials and conditions. The robust approach is, therefore, to make a direct measurement of the fracture toughness.
Chad Haegelin1, Luke Whitrock2
1Integrity Solutions Ltd, Houston, USA. 2Integrity Solutions Ltd, Denver, USA
Many pipeline operators are still experiencing internal corrosion issues despite implementing industry best practices. Due to the ever-expanding regulations, operators are required to be more proactive in preventing corrosion on lines not previously regulated.
PHMSA and API have both implemented industry best practices and advisories to move closer toward a predictive approach to integrity management, with the ultimate goal of improving corrosion detection and identifying mitigations.
This presentation examines multiple real-world operational scenarios where the application of a quantitative internal corrosion (QIC) model has proactively helped pipeline operators working in field operations, chemical teams, and integrity management departments, risk-optimize mitigation, inspection, and monitoring activities as a strategy for eliminating failures.
The QIC Assess (pronounced Quick Assess) model is designed to effectively predict location-specific internal corrosion rates throughout a pipeline in a time-based cumulative degradation prediction. This model employs pipeline-specific flow parameters derived from a detailed pipeline hydraulic model designed to disentangle the complexities of multiphase fluid flow influence on the internal corrosion growth mechanism.
We’ll present case studies demonstrating how an operating company went from leading the industry in pipeline failure frequency rate to eliminating all pipeline leaks within 4 years of implementing our QIC Assess model and embracing the mitigation recommendations. In another implementation of the model, we’ll discuss how the model accurately predicted moderate bottom-of-pipe internal corrosion and severe top-of-pipe internal corrosion.
Ahmad Al Saif, Nouman Tehsin, Mohammed Al Rabeeah
Saudi Aramco, Dammam, Saudi Arabia
One of the most growing Integrity Management Programs in liquid buried pipelines is the management of Stress Corrosion Cracking (SCC). Detecting and sizing SCC in liquid pipelines are usually achieved by utilizing Ultrasonic Crack Detection (UTCD) In-Line Inspection tools. Although the UT technology has been established in the industry for a long time, UTCD ILI data is still complex to analyze and interpret. Unlike the Magnetic Flux Leakage (MFL) tools, the accuracy of crack identification and sizing by UTCD tools has high sensitivity to temperature, pipe roughness and debris content. However, the accuracy can be further enhanced by calibrating the tool after conducting some verification digs and providing the field data (i.e.: crack depth, crack length); to the ILI service provider.
This paper introduces a very challenging case study for one of Saudi Aramco Liquid Pipelines that experienced a significant increase in number of the reported crack features between two UTCD ILI runs. The pipeline was inspected by the same UTCD technology in two consecutive years. Yet, the latter run reported a significantly larger number of cracks compared with the first one. Since cracks are not normally initiated within one-year span, a systematic approach was followed in order to identify all potential root causes of this increase. Before identifying the potential root causes, it is deemed necessary to verify newly reported cracks in the field. Therefore, the quality of the recent UTCD run was determined based on two aspects: comparing the recent UTCD data with field results and then comparing the raw data of the recent UTCD run with the previous UTCD run. After conducting comprehensive assessment, the latter ILI UTCD run was found to be below the performance specifications and hence below the acceptable limits as per API-1163.
Douglas Sahm
ZEVAC, Tulsa, USA
An impact-based approach to integrity management in the context of the EPA’s new “Super Emitter” program is detailed with case-study and practical guidance for operators to navigate their IMP operations while avoiding the 100kg/hr methane emission threshold for super emitter classification. The EPA’s new OOOOb/c rules have established a 3rd party reporting mechanism that will impact nearly all blowdown or purge operations within an operators’ integrity management program. Pigging, line blowdowns, hydrotesting, and cutouts will all be considered super emitters if procedures are not updated to avoid the associated gas releases. Many techniques that have been developed in the sour gas, refrigerant, and volatile liquids industries have been adapted to allow for minimal release during gas line integrity operations.
Mussab Al-Nammi, Khalaf Al-Anazi, Mohammed Al-Rabeeah
Aramco, Dhahran, Saudi Arabia
A case study was conducted on a sour gas service pipeline with high H2S concentration. The aim of the study was to evaluate the current condition of the pipeline and to provide a solution to perform the In-line Inspection (ILI) base run. The sour gas service pipeline was constructed in 2012, has been operating since 2013, and has over 50 KM in length with a size of 20" in diameter.
As part the commissioning, a caliper run was conducted to assess the pipeline’s internal diameter, which revealed that there were no restrictions or dents in the line. After the pipeline was commissioned, ILl runs were scheduled as per the standard requirements, to inspect the newly commissioned pipeline to ensure full integrity. A gauging run was conducted to assure pipeline mechanical readiness for the ILI run.
The gauging run resulted in an unsuccessful run due to considerable damages in the tool and huge amount of debris (more than 1000 kg). A following gauging run was conducted after assuring that all valves were fully opened, which resulted in an unsuccessful with the same damage profile as the previous run.
Given the unsuccessful gauging runs, a caliper run was conducted to identify the obstacle. The caliper tool was retrieved with severe damages and was inconclusive with regards to the internal obstruction.
A comprehensive assessment on the pipeline was conducted to evaluate the causes of the damages, which revealed that the damage was due to hardened debris within the pipeline as a consequence of improper chemical cleaning that was implement after the line was in-service.
The assessment recommended a cleaning campaign with specialized spring-loaded cleaning tools with magnets followed by a caliper tool. The cleaning campaign contained a minimum of thirty back-to-back aggressive cleaning runs. After completing the cleaning campaign, the caliper tool was conducted successfully and the internal restriction was negotiable by utilizing the 18/20" ILl tool, which was conducted successfully. This cleaning campaign resulted in a successful revalidation of the pipeline.
Brian Cooper, Jonathan Ferris
ADV Integrity, Grand Rapids, USA
This paper presents the results of a review of recent major pipeline failure investigations by the National Transportation Safety Board (NTSB). Investigations conducted after loss-of-containment failures reveal opportunities for root cause analyses that, if conducted after the failure of a single threat barrier, could have prevented the later loss-of-containment failure. Recognizing these opportunities proactively rather than in hindsight is challenging. This study provides insight into the factors that emerge from the recent major pipeline failure investigations reviewed that can support the proactive identification and prioritization of single-barrier failures for root cause analysis and corrective action.
Dr Tom Bubenik is a Vice President at DNV USA, where he is responsible for developing, managing, and implementing projects related to all aspects of pipeline integrity management, including but not limited to ILI, SCC, fracture control, seam weld integrity, and mechanical damage. He has over 45 years of related pipeline experience. Dr Bubenik is an internationally recognized expert in technologies related to in-line inspection and the effects of defects on pipeline integrity. He received his PhD in Theoretical and Applied Mechanics from Northwestern University.
Avenida North Garage rates
Willem Vos, Jan Ove Toskedal, Gary Dye
NDT Global, Bergen, Norway
In the early 21st century, a team of researchers in DNV (Norway) developed an ultrasonic technology for the inline inspection of gas pipelines without liquid batch. The dry-ultrasound technology has subsequently been used to inspect more than 10,000 miles of operational gas and liquid pipelines around the world.
The authors present lessons learned during the deployment of this new technology and reflect on the advantages and limitations.
Several different use cases are considered; one being deployment of acoustic resonance ILI for the base line inspection of newly constructed gas pipelines. In particular, the others will highlight a number of long-distance gas transmission pipelines that have been inspected using acoustic resonance ILI, and highlight the benefits of ultrasonic baseline for pipelines.
Furthermore, the tools have shown notable flexibility in the field of difficult-to-inspect gas and liquid pipelines. Notably, large diameter variations have been traversed, and bidirectional inspections have been performed, as well as extremely long duration runs.
A summary of completed work will be of value to all pipeline operators of challenging pipelines, in particular offshore, demonstrating challenging pipeline inspection projects which have been completed successfully.
Ian J. Duncan1, Alex Lange2, W. Kent Muhlbauer3
1Univ. of Texas-Austin, Center for Assessment and Management of Risk (CAMR), Austin, USA, 2Summit Carbon Solutions, Ames, USA 3WKM Consultancy, Austin, USA
There are significant misunderstandings surrounding transport of CO2 in pipelines. Robust risk assessments, including proper dispersion modeling and characterization of possible health effects, are essential to proper understanding of the actual safety of pipelining CO2. As part of a national initiative related to climate change, it is imperative that real information is readily available, especially to technical audiences. This paper explores several of the more significant points of confusion/controversy.
Nikolaos Salmatanis1, Amit Rajput2, Praveen Kumar2, John O’Brien3
1Chevron, Houston, USA. 2XaaS Labs, Sunnyvale, USA. 3itcSkilla, Houston, USA
Reliable detection and accurate localization (especially) of small leaks tends to be the weak link in Leak detection programs for oil & gas pipeline operators. The paper presents the results of a study aimed at assessing the feasibility of reliably identifying pipeline leaks using inline approaches based on minimally intrusive sensing devices that are now available to pipeline operators. These low form-factor sensing devices incorporate sensors based on Audio, Magnetometry, Pressure and Velocity. A test pipeline flow loop was leveraged to create a customized test setup and a test execution methodology was developed and executed towards this end. Sensing equipment from two different suppliers were used to collect various sensor datasets on separate test runs In test scenarios where leak signatures were identified, the team investigated the feasibility of ascertaining the limits of detection using such approaches. Key findings and Lessons learned are summarized
Click the button below to download all the PPIM 2024 Conference Papers in one pdf file
(file size: 402MB)
Rick Wang1, Ming Gao2
1TC Energy, Calgary, USA. 2Blade Energy Partners, Houston, USA
In API1183, the EPRG 2000/API579 Level 2 model is adopted as an alternative approach to BMT shape-parameter method for Level 2 fatigue severity assessment of unconstrained single peak plain dents in pipelines This model along with its earlier version, EPRG 1995, has been commonly used for dent integrity assessment in North American and worldwide because it is recommended by the highly recognized pipeline defect assessment manual. However, Pipeline industry practice in North America found that the EPRG equations provide conservative, in many cases, very conservative predictions that may have resulted in unnecessary excavations and repairs. Therefore, the objective of this paper is to improve the model accuracy and less conservatism. A critical review of EPRG/PDAM fatigue life prediction models (1995 model and its 2000 update) and other models including PRCI/BMT shape-parameter fatigue severity model (Level 2) and FEA/BS7608 fatigue life prediction (Level 3) are essential and given first, which provides a basis for improvement of EPRG equations from both safety and cost-effective perspectives. The newly improved and simplified model is then developed with PRCI MD 4-2 full-scale fatigue testing data and validated using PRCI MD 4-11, MD 4-14 and MD 4-15 full scale fatigue test results. Finally, a comparison among the newly improved model, EPRG 2000/API 579 Level 2 model, and PRCI/BMT/API 1183 Level 2 and Level 3 models is made, which provides a framework to further carry out the study of dent-interacting with welds, gouge, cracks, and corrosion.
Kah Soon grew up in the oil & gas city of Miri, Sarawak (Borneo-Malaysia). He graduated from the University of Manchester (UK) with a MEng in Mechanical Engineering with Management. He started his career as a subsea and pipelines design engineer and was involved in various offshore field development and installation projects across the African and Asian regions. Currently as a Technical Solutions Specialist for ROSEN focusing on pipeline integrity, Kah Soon hopes his experience in design & engineering will bring a different approach to integrity assessments that are largely anomaly-focused.
After participating in various conferences, Kah Soon noticed a gap in the energy industry: there was a lack of focus on pipelines in Southeast Asia (SEA). Aligning with YPP Malaysia’s mission and as one of its founding members, he has organized various pipeline-based technical and networking events. As the current Chair of YPP Malaysia, Kah Soon hopes that these events will create an increased level of industrial awareness and appreciation towards pipeline assets and its professionals in SEA.
Blake is a passionate advocate for the oil and gas industry and has spent more than 10 years in various technical and project management roles in the midstream sector. He currently works for Audubon Companies in New Orleans, LA as a Project Manager. Blake received his Bachelor of Science in Civil Engineering from Louisiana State University in 2014, his Masters in Business Administration from the University of Houston in 2018 and is a certified PE in several states. He is known for his enthusiasm and dedication to sharing his positive messages and insights with others. He is an active leader of Young Pipeline Professionals (YPP) USA and has been engaged in several other young professional organizations throughout his career. Blake is also active within the INGAA Foundation, the Southern Gas Association’s Multi-Generational Leadership Committee and serves on SGA’s Executive Council. Blake’s passion for the industry and his commitment to knowledge transfer and young professional advancement have earned him respect and recognition both within and outside of his organization. He is a valued member of the industry, and his contributions continue to make a positive impact on the industry and the communities he serves.
James Dean
Plastometrex, Cambridge, UK
Indentation Plastometry is a novel approach for measuring stress-strain curves from indentation tests. It differs from scratch testing and Instrumented Indentation Testing (IIT) in several important ways – all of which are covered in the presentation. The underlying scientific methodology (an accelerated inverse finite element analysis) is also discussed in detail. A new tool for in-ditch Material Verification that employs Indentation Plastometry is now available and in use, but to support its adoption on oil and gas transmission pipelines, the tool has recently been subjected to a period of intense validation in cooperation with several network operators, several service providers, and the PRCI. By June 2023, 125 pipes had been tested. Those test results indicated that the tool has industry-leading accuracy levels (MAPE numbers) which is expected to be of interest to pipeline integrity management teams. These assertions have been corroborated through independent analyses of the validation testing data by RSI Pipeline Solutions LLC. In addition to MAPE numbers, alternative metrics for characterizing the accuracy of this and other tools for material verification were also examined (through tests conducted on the same pipe samples). These statistical methods included Clopper-Pearson, Hanson-Koopman, a one-sided prediction interval method, and a linear regression method, with the outcome being that Indentation Plastometry is extremely well suited for fast, accurate and repeatable measurement of pipeline material properties.
The presentation will cover the details of the validation testing journey, the validation test results, and the statistical analyses that were conducted. Further results obtained between June 2023 and February 2024 (predominantly through blind network qualification tests) will also be covered.
Morgan Dormaar1, Derrick Hunter1, Cory Solyom2, Dixit Patel3, Wade Forshner4, Michael Callan5
1PureHM, Edmonton, Canada. 2PureHM, Calgary, Canada. 3TC Energy, Calgary, Canada. 4Pembina Pipeline, Calgary, Canada. 5Keyera Corp, Grand Prairie, Canada
Although a lost or stuck pig is rare, when it does occur, the costs can be extremely high, raising the location efforts to the highest priority.
A lost or stuck pig in a pipeline can have a serious impact on an operator’s ability to transport product. While uncommon these days, this does still occur, and when it does it can be detrimental to the safe and efficient operation of an Oil and Gas pipeline. Therefore, the ability to identify the location of the obstruction quickly is of utmost importance and can become a singular highest priority for the pipeline operator. Recent advancements in technology have facilitated such locating efforts, and saved operators time, expense and aggravation.
Oil and Gas pipelines are comprised of ferromagnetic materials, such as iron, nickel, steel and other materials. Large Standoff Magnetometry (LSM) technology is known to be used to identify and locate elevated levels of stress through the measurement of the magnetic field surrounding steel pipelines. LSM detects inverse magnetostriction (also known as the Villari effect) which is the change of the magnetic susceptibility of a material when subjected to mechanical stress. LSM technology has been used to detect defects as they appear as changes in the magnetic field around the pipeline which can indicate the presence of stress on the pipe. Thus, LSM can identify stress concentration caused by full pipeline blockages.
This paper will discuss how the XLI PWA technology works to locate lost or stuck pigs, and review 3 successful case studies.
Case Study 1 will discuss locating a lodged MFL tool in a 42” Gas pipeline. PureHM worked with TC Energy to locate an MFL tool that had become lodged in their line. TC Energy was ready to excavate and cut the tool out but required confirmation that they were in the right area before investing significant resources into the tool retrieval process, PureHM was able to mobilize and confirm tool location in a single day.
Case Study 2 will explore a project where a pig was lost and was fully obstructing the pipeline. Pembina provided several potential locations where the pig was thought to have stopped moving. Within 2 days PureHM was able to locate the stuck pig and the front of the blockage. Pembina was able to free up the stuck pig by Hot-Tapping.
Case Study 3 will present a more complex project where PureHM worked with Keyera to identify the location of multiple stuck pigs that were being obstructed by a wax slug in a 4-inch pipeline. PureHM worked over a period of 4 days to identify the location of the 2 stuck pigs. Keyera was then able to heat the pipeline at the location identified by the XLI PWA Technology and melt the wax obstruction to get the pipeline operational again.
Brian Ellis1, Louise O’Sullivan2, J Aidan Charlton2, Ben Lowry3, John Norman3, Jake Opdahl3
1pipelinelogic, Lakewood, CO, USA. 2Penspen, London, UK. 3Teren, Inc., Lakewood, CO, USA
The integration of pipeline digital twins with geohazard modeling presents a groundbreaking approach to enhance the safety and resilience of critical energy infrastructure. This presentation explores the synergy between pipeline material data, inline inspection technology, and advanced geohazard modeling techniques to create comprehensive geohazard threat assessments.
Traditional geohazard assessments often rely on limited data sources, leading to potential vulnerabilities in pipeline systems. However, by combining detailed pipeline material information and high-resolution inline inspection data, a more accurate and robust representation of the pipeline’s condition and vulnerabilities can be achieved. These digital twins provide a dynamic and real-time view of the pipeline’s integrity, enabling proactive maintenance and risk mitigation strategies.
The core of this presentation delves into the following key areas:
In conclusion, the integration of pipeline digital twins and geohazard modeling represents a transformative paradigm shift in pipeline management. This presentation demonstrates how this innovative approach empowers pipeline operators to proactively identify and mitigate geohazard-related risks, ensuring the long-term reliability and sustainability of energy infrastructure.
KEYWORD(S) FOR SUBJECT AREA: Geohazards, Geospatial Systems and Data
Kirsty McDermott1, Andy Fuller2, Chris Lyons2, Andy Brealey3, Jeffery Stephen Jones3, Neil MacKay4
1National Gas Transmission, Warwick, UK. 2PIE, Newcastle, UK. 3DNV, Loughborough, UK. 4STATS, Aberdeen, UK
National Gas Transmission own and operate the National Transmission System (NTS), the backbone of British Energy. The NTS feeds homes and businesses the essential gas required for life today in the UK. When operating above 70 bar, like most of the network does, the potential of failure or downtime of these pipelines has a critical impact on how interventions are carried out. However, changing how we do these interventions isn’t as simple, but why can’t we just make it so?
In line isolation tools have never been used on downstream onshore pipelines in the UK before. Regardless of the experience of others, NGT must assure itself through a process of due diligence that the new technologies and techniques do not create an immediate threat, or future integrity threats to the remaining life of the pipeline. NGT has developed an approval process, and has been trialling and testing tools, to develop an unbiased viewpoint built on evidence on the operational acceptance and integrity implications for the pipeline.
NGT has conducted an Isolation Joint replacement using a Pipeline Isolation Tool, instead of traditional venting (emissions reduction) and the need for recompression operations or alternative more invasive options (stoppling and bypass). The technology provided a fail-safe, leak tight double block, and monitor isolation, keeping a 48” pipeline fully pressurized at 56bar for 56km to the nearest block valve upstream. This method can help to reduce NGT’s emissions and operators’ exposure to high hazard methods.
Colin Scott, Abu Hena Muntakim
Northern Crescent, Calgary, Canada
Stress corrosion cracks are typically found in colonies comprised of multiple parallel aligned cracks. However, they are usually assessed as individual (or single interlinked) cracks, assuming the deepest of the colony represents the crack driving force for failure. This common approach does not account for the effects of crack shielding. It is known that neighboring cracks may dissipate stress intensity and result in a lower crack driving force.
In this work we use FEA to estimate the stress intensity factors associated with crack colonies. Results demonstrate how stress intensities in colonies are decreased relative to those of individual cracks. This is consistent with recent industry model studies that tend to underestimate critical failure pressures of in-service SCC flaws. It also indicates a fracture mechanics contribution to the known phenomenon of crack dormancy, which is often attributed to electrochemical and kinetic factors. The findings can be used to modify fitness for service assessments and improve SCC integrity program efficiency.
Mick Ellem1, Mark Sigley1, Olivia Chung2
1First Gas Limited, New Plymouth, New Zealand. 2Quest Integrity NZL Limited, Wellington, New Zealand
First Gas operates the natural gas transmission pipeline network in New Zealand. In 2022, crack-like linear indications on the long seam of the pipeline were identified by non-destructive testing (NDT) carried out opportunistically during coating refurbishment of a length of pre-1971 pipeline. Quest Integrity were engaged to investigate these crack-like linear indications. Metallurgical analysis of coupons removed from the pipeline concluded that the crack-like linear indications observed were Selective Seam Weld Corrosion (SSWC). With knowledge of this new threat, First Gas initiated a work program to manage this risk in the pipeline.
The work program included a Like-and-Similar analysis of the three most recent Magnetic Flux Leakage (MFL) metal loss ILI data sets collected in the pipeline and metallurgical analysis results, and additional field verification using advanced ultrasonic methods to further characterize metal loss features interacting with the long seam. Corrosion growth rates determined from the Like-and-Similar analysis and characterization of features detected ultrasonically and/or metallurgically verified were utilized in a Fitness-for-Service and remaining life assessment of external metal loss features, both interacting with and away from the longitudinal seam weld.
First Gas used the results obtained from the above investigation to update their integrity management plan for their pre-1971 pipelines, now including management of the threat posed by SSWC. This paper presents the full scope of work performed by First Gas and Quest Integrity to manage the threat posed by SSWC for the pre-1971 pipelines and shares the learnings obtained from the process.
Keywords: ERW pipe, Pipeline integrity management, Corrosion, Selective Seam Weld Corrosion, Crack-Like Features
Kerstin Munsel1, Thomas Meinzer2
1NDT Global, Houston, USA. 2NDT Global, Stutensee, Germany
When a pipeline is inspected, recorded pipeline data is manually or automatically evaluated. Regardless of the pipeline condition (such as degree of corrosion), once the features meet performance specification requirements, the data analysis and its result are in no way affected.
But what about inspections that, for various reasons, do not correspond to the standard and feature complexities are at the limit of the performance specification or are completely below it? What if the feature is still detected but not recorded correctly and the data evaluation is permanently impaired or appears impossible at first glance? What if the relative position of the features further increases the complexity of the analysis? Is it still possible to extract the essential information from the recorded signals?
Even under difficult conditions, detailed UT data analysis can provide high-precision results. This was evident in a non-standard 6″ project, confirmed by field measurements, and will be presented in more detail in this paper.
KEYWORD(S): 6” pipeline, challenging internal corrosion anomalies, non-standard analysis
Seyed Hamed Fatiminia1, Eduardo Munoz2
1Dynamic Risk, Calgary, Canada. 2Dynamic Risk, Houston, USA
Sensitivity analysis is paramount for improving the accuracy and robustness of oil and gas pipeline quantitative risk models. As a result, sensitivity analysis of the risk models is now a requirement under §192.917(4)c of the Gas Mega Rule – Part 2 for gas pipelines. The inherent complexity and interdependency of factors influencing pipeline risk require an in-depth comprehension of the sensitivity analysis methods. Fitness-for-service calculators are integrated into some quantitative models; though extensive validation work has been reported, a proper sensitivity analysis has often been omitted in benchmark studies and reviews. The primary objective of this paper is to provide an in-depth review of various sensitivity analysis techniques, highlighting their strengths, limitations, and practical applications in pipeline risk assessment. The comparative analysis is conducted based on multiple criteria, comprising computational efficiency, accuracy, ability to capture interactions between risk variables, and suitability for handling uncertainties inherent to pipeline systems. The findings of the comparative study provide valuable insights into the strengths and limitations of various methods, aiding practitioners in selecting the optimal sensitivity analysis technique based on their modeling objectives and data availability. Real-world case studies are provided to illustrate the practical application and results of some of these techniques.
Woosik Kim1, Dongil Kwon2, Dongseong Ro3
1FRONTICS INTERNATIONAL Inc, Seoul, Republic of Korea. 2Seoul National University, Seoul, Republic of Korea, 3FRONTICS AMERICA Inc, Mount Prospect, USA.
US federal rules, DOT 49 CFR §192.607, require that records documenting physical pipeline characteristics and attributes, including diameter, wall thickness, seam type, and grade, must be maintained for the life of the pipeline and be traceable, verifiable, and complete. Specifically, the PHMSA report on the integrity verification of ERW seam pipelines highlights the significant impact of local properties on failure pressure and remaining life predictions and thus reinforces the development of inspection tools in routinely quantifying local strength and toughness of materials.
This paper investigates the effects of different ERW seam manufacturing processes on the local microstructure and mechanical properties of seam welds on operating pipelines using AIS system of FRONTICS Inc. The instrumented indentation technique, followed by additional microstructural observations, was utilized to assess hardness, tensile properties, and fracture toughness of LF ERW and HF ERW pipes with different manufacturing years. Ultimately, this paper will present a strategy for the non-destructive analysis of operating ERW pipelines, simultaneously providing a classification guideline on seam welding methods and pipe integrity assessment.
Russell Giudici¹, Ahmed Hassanin², Atul Ganpatye², Chris Alexander²
¹Advanced FRP Systems, Weymouth, USA, ²ADV Integrity, Magnolia, USA
ABSTRACT
Non-metallic, composite reinforcement systems for pipes have become a standard method for repairing a range of defects including corrosion, dents, gouges, cracks, girth welds and seam defects. Composite repairs for pipes are hand applied in the field, making application defects a potential source of concern, especially for larger repairs and hard to reach areas. The most common defects observed are air pockets trapped within the layers of the composite wrap.
This paper explores the effects of air bubbles of varying sizes and depths within the composite repair system. Specifically, we will look at the effects on the pressure capacity of repaired pipes with designed defects by performing live, hydrostatic pressure tests. We will also look at the effects of air bubbles on the liquid tightness of composite wraps that are applied on pipes with through wall failures. Finite element analysis was performed to analyze any additional stresses on the composite wrap system with air pockets of various sizes and at a variety of locations within the composite reinforcement system. Finally, we will look at the results of both the physical pressure testing as well as the computational analysis to help provide real world guidelines to determine when air bubbles require repair in the field.
Rhett Dotson1, Briant Jackson2, Matt Stevenson2, Chris Newton2
1D2 Integrity, LLC, Houston, USA. 2Phillips 66, Houston, USA
Many pipeline operators have performed bending strain assessments based on IMU data and received results that are challenging to interpret and properly sentence, especially if the assessment identified hundreds of features. These challenges can be compounded if the operator acquires a second IMU data set and elects to perform another bending strain assessment or a comparison assessment between the two data sets. In these situations, operators often observe significant variations in the number of reported bending strain features and the reported strain magnitudes associated with those features. These challenges can rarely be solved by comparing the final reports as the graphical information for the bending strain features is often rendered differently between vendors. This paper presents the results of a case study comparing four IMU data sets acquired over a decade on the same pipeline segment where the number of reported features varied from 195 to 384. The paper examines the causes of this variation in reported features including the influence of gage length, signal noise, and analyst judgement. The case study also identifies common challenges that occur when comparing multiple IMU data sets and provides strategies for recognizing and overcoming these challenges. The paper concludes by identifying how bending strain reporting requirements can be standardized and help operators minimize these challenges in future assessments.
Joel Van Hove1, Casey Dowling2, Pete Barlow3
1BGC Engineering Inc., Vancouver, Canada. 2BGC Engineering Inc., Golden, USA. 3BGC Engineering Inc., Edmonton, Canada
Well-structured geohazard management programs (GMPs) for pipeline systems have become common over the last two decades in North America as pipeline companies have become more aware of the risks presented by natural hazards and the value in adopting proactive approaches to manage risk. The case study presented in this paper represents the GMPs of 30 major pipeline companies in North America comprising approximately 100,000 miles of operating and actively managed pipeline. The performance of these GMPs has been measured to reduce pipeline failure rates from geohazards 4 times. Over the past 10 years more than 95% of the observed geohazard pipeline failures have been from slow-moving landslides. The study scope includes approximately 10,000 landslide crossings. The annual probability of failure given pipeline impact from a slow-moving landslide has previously been estimated at 1 in 50, meaning any landslide which is actively moving and intersecting a pipeline presents a potentially serious integrity concern. The primary challenge with managing slow-moving landslide hazards is that determining landslide activity without instrumentation is often not possible, and installing conventional instrumentation such as slope inclinometers at such a large number of landslides is prohibitively expensive. Slow moving landslides also cannot reliably be visually identified as movement rates are often low enough that visible surface disruption is subtle or undetectable, but those same movement rates will be enough to cause pipeline failure over the life of the pipeline. To address this challenge many forms of low-cost instrumentation have been pursued to measure ground movement and/or pipeline impact including Interferometric Synthetic Aperture Radar (InSAR), lidar change detection, and in-line inspection tools such as axial strain and inertial measurement unit (IMU). Over the last 10 years IMU has become a critical and frequently utilized tool for assessing landslide activity and has been integrated into the geohazard management programs of all the operators in the study scope. In 2022 IMU was credited for identifying 53% of the active landslides where operators completed critical interventions to manage risk (e.g., pipeline shut in, stress relief mitigation). Key lessons and observations for successfully integrating IMU into GMPs are presented from a case study spanning 10 years and 100,000 miles of pipeline.
Megan Grzelak1, Trevor Ortolano2
1NiSource, Merrillville, USA. 2Campos EPC., Denver, USA
The intent of this technical paper is to illustrate a repeatable approach to validating station assets through a complete records and material verification process to better understand MAOP Reconfirmation.
By utilizing modern technology, established best practices and detailed records research, one can generate a near complete understanding of the assets at a particular facility. Using the data gathered from records and subjecting it to effective tooling with the use of a file geodatabase, the operator can understand the compliance challenges of these assets spatially and better prepare for the execution of MAOP Reconfirmation. A final, but not to be overstated, aspect of this program is a demanding definition of Traceable, Verifiable and Complete records that is well understood by all parties involved.
To better aid the understanding of the results, a series of “one line” isometric drawings are also created to act as a visual aid relative to requirements like pressure test coverage, %SMYS, Work Order History, etc. These tools are especially effective when presenting large stations (multiple settings built and upgraded over many decades) to the various stakeholders for their input and support as this evidentiary process becomes a plan of action relative to MAOP Reconfirmation.
With these deliverables [file geodatabase (FGDB), single line isometrics and a final report with relevant information and appendices] an operator can assess gaps in Compliance Material and explore further material verification efforts to mitigate the impacts of MAOP Reconfirmation to their respective systems and budgets.
While the initial efforts of this program are geared predominantly at executing MAOP Reconfirmation, by introducing the FGDB at the onset, the operator can develop a living data organism that has many applicable uses to many departments within an operator’s organization over the life of that facility.
Categories: MAOP Verification and Materials Verification
Daniel Bahrenburg1, John Norman2, Jeffrey Haferd3
1ROSEN USA, Houston, USA, 2Teren 4D, Lakewood, USA, 3Marathon Petroleum, Findlay, USA
Landslide threats continue to be a prevailing concern for pipeline operators and the public. Although several methods and technologies exist to detect and monitor these geohazards, determining what strategies are most effective and efficient for integrity management can be challenging. High-resolution inertial measurement (IMU) data can be utilized to detect anomalous strains resulting from pipeline displacement. The knowledge of experienced geotechnical experts can then be leveraged to review and characterize geohazards coincident with these anomalies in more detail. Although this strategy is extremely effective, timely and detailed geohazard reviews can be challenging due to a manual analysis process and expert availability. However, without expert review, pipeline company integrity managers can be left with concerns regarding how to determine what results constitute an actual concern for the pipeline. To streamline efforts to prioritize landslide-affected pipelines, Marathon Petroleum has adopted an alternative, highly efficient approach to geohazard screening, which incorporates IMU-based bending strain assessments and automated geohazard detection/characterization using high fidelity LiDAR (Light Detection and Ranging) data. This paper will present a brief overview of the ROSEN method of pipeline movement detection using IMU data from multiple in-line inspections, followed by an outline of the Teren method for streamlined geohazard screening and severity assignment. To conclude, a review of several case studies will provide examples where a combination of high strain and/or pipeline movement was detected coincident with high-severity landslides based on an Absolute Geohazard Assessment (AGA) score for areas of confirmed slope movement.
Rhett Dotson1, Jeff Haferd2, Karim Kabbara2, Nic Roniger2
1D2 Integrity, LLC, Houston, USA, 2Marathon Pipeline, Findlay, USA
The use of bending strain analyses for identifying and managing pipeline geohazards has grown significantly in the last decade. While bending strain assessments are useful for identifying and prioritizing geohazard features impacting pipelines, it is understood that bending strain assessments cannot provide the total strain which is required for comparison to calculated tensile or compressive strain capacities in determining fitness for service. The inability to easily calculate membrane strain and the resulting total strain in impacted pipelines represents a gap in the industry. A few simplified methodologies have been proposed to estimate the membrane strain based on the displaced shape of the pipeline, and some newer ILI technologies are available for explicitly measuring the membrane strains. Level 3 numerical analysis is another method that can be used to estimate the membrane, bending, and total strain states in a pipeline impacted by a geohazard. This paper presents the results of a study covering nine finite element analyses completed on separate geohazards with varying characteristics. The paper discusses the methods used in the study to construct the models, including incorporating initial strains and estimating as-built conditions of the pipeline. Comparisons are provided between the membrane strains calculated explicitly in the models and membrane strains estimated using simplified methods. The study examines how membrane and bending strains develop and progress at larger pipeline displacements noting important differences in axially and laterally oriented geohazards. The conclusions from this study provide useful insights to operators on how to perform level 3 geohazard assessments, and how to properly use the results to make informed integrity management decisions for monitoring or mitigation or geohazards threats.
Mohamed Elseify, Jeff Sutherland
Baker Hughes, Calgary, Canada
Pipeline systems experience a range of strain conditions along their length. These are either factored into the pipeline design as known operational strains or as strain resulting from additional external loadings that are potentially unknown during the design or construction phases. Detecting, monitoring, and understanding these additional strains in combination with operational strains are a key part of a pipeline integrity management program. Surveying with inertial mapping tools have been commonly used since the late 1980’s for accurate measurement of bending strain – which unfortunately only provides a part of the picture. The development of the ILI axial strain measurement tool (AXISS™) was a response to fulfilling a pipeline operator’s need for axial strain measurement in combination with available bending strain information to enhance their geohazards risk management programs.
After a long period of comprehensive field testing and validation, supported by a number of partner customers, Axial Strain Inline Inspection transitioned from a developmental to commercial service more than 10 years ago. Since then, over 20,000 km of data has been collected with many high strain locations successfully identified and mitigated. While axial strain inspection is now established as a proven and important tool for a pipeline operator to assess geohazard and other strain related threats, that experience has provided key insights as to where the current technology strengths lie and of course where we need it to go next to provide the level of information truly needed to optimize our full understanding of strain-based threats. This paper gives a detailed overview of some of those experiences discussed, examples of the applications of the technology and the types of strain events identified. Secondly, and more importantly, this paper provides key insight into the latest developments of the technology that will address the remaining unmet needs of the geohazard and stress engineers tasked with establishing a complete picture of pipeline strain condition, allowing them to effectively optimize any mitigation measures or repair programs.
Tristan Jones, Ivan Thesi, Cesar Espinoza, Andres Gonzalez, David Bastidas
ROSEN, Houston, USA
According to 2018 PHMSA Stakeholder Communications Fact Sheet, an estimation of 18% of pipeline failures in the United States (from 1998-2017) were caused by corrosion. Calculating accurate remaining strength of corroded pipe with complex corrosion, such as axially aligned clusters with multiple pitting on pitting metal loss anomalies, has historically been a challenge for operators. Traditional Effective Area Methods (EAM) for assessing the remaining strength of complex corrosion anomalies, such as Modified B31G and Detailed RSTRENG can lead to overly conservative results and extensive repair campaigns. In these cases, it is difficult for operators to distinguish between the critical repairs and uncertainties, potentially preventing them from focusing resources into other pipeline mitigation activities. A more detailed evaluation of corrosion geometry through an advanced fitness-for-service method, known as Plausible Profiles (Psqr), can be used to gain a better estimate of the remaining strength of pipeline areas with complex corrosion. However, it is important to understand when this method is applicable and when it will yield the most benefits for pipeline operators. With proper selection criteria, ideal candidate corrosion anomalies can be identified for this method, which will add efficiency to the pipeline remediation process and provide more accurate results. This paper will discuss the criteria for selecting corrosion anomalies for implementation of the Psqr method in combination with a rationalized repair strategy. The selection criteria consider aspects associated with anomaly morphology, assessment depth, length/width ratio and potential failure mode. This paper will present how a number of excavations was reduced by more than 70%, with no impact to public safety, based on a case study of a natural gas pipeline. The remaining strength of 60 corrosion anomalies was extended, facilitating the optimization of the maintenance planning and expenditure, and supporting the pipeline Integrity Management Plan (IMP).
Casey Dowling1, Pete Barlow2, Joel Van Hove3, Teko Hanvi4, Jim Hart5
1BGC Engineering USA, Golden, USA. 2BGC Engineering, Edmonton, Canada. 3BGC Engineering, Vancouver, Canada. 4Enbridge. 5SSD, Inc.
Inertial measurement unit (IMU) bending strain data has been recognized as a crucial tool in detecting ground movement impact along operating pipelines. In Line Inspection (ILI) vendors produce bending strain and movement reports which often include impact from landslides and sinkholes, but also include a host of other causes. While these bending strain reports serve as a useful initial screening tool, previous studies have found that approximately 90% of these reported features are related to pipeline construction or operation, not ground movement impact. It is not uncommon for hundreds of bending strain features to be reported on a single 100-mile pipeline segment, and it is important for pipeline operators to be able to quickly differentiate ground movement caused bending strains. Unlike construction-related bending strains, ground movement tends to increase strain demand over time and often has a larger longitudinal strain component because of axial loading or pipe elongation. Often, landslides and sinkholes produce readily apparent signatures in IMU data that are evident during a cursory review. Drawing upon 10 years of experience using IMU data to characterize and monitor geohazard impact along pipelines and geotechnical assessment of more than 6,500 bending strain features, this paper provides examples of common IMU signatures indicative of landslide and sinkhole impact with the intent that operators can learn to spot the most obvious potential geohazard impact sites and prioritize those for further assessment or action. Examples of signatures from single run and run-to-run IMU data are presented along with a discussion of the basic mechanisms that produce the signatures. Key ground-movement signatures within other IMU outputs such as pitch, heading, and position are also discussed. Construction-related IMU signatures are provided to help operators understand how these differ from ground movement signatures.
Wes Gardner
STATS Group, Calgary, Canada
Operators can often encounter difficulties in isolating sections of their pipeline to facilitate essential safe repair or maintenance activities if appropriate valves are absent from the line. In-line isolation pigs provide fully proven and monitored dual seal barriers that ensure the safe breaking of containment on pressurized systems in compliance with the highest industry standards.
Unlike traditional Line Stopping activities, piggable isolation tools require no welding or cutting into live lines, leaving no residual fittings or hardware on the pipeline. This eliminates project costs associated with fittings, welding and inspection and reduces the risk of leak paths from buried pipeline flanges post operations.
Line stopping often requires pipeline excavation and site establishment including lifting and rigging operations which is usually eliminated by deploying inline isolation pigs. Tracking, operation and communication with in-line isolation pigs can be achieved remotely through ground and pipe wall preventing the need for costly site establishment and reducing the risk of digging and lifting operations around the pipe.
In-line isolation tools significantly reduces, and in some cases eliminates, the requirement to vent or flare harmful emissions into the atmosphere during maintenance activities. One of the most significant environmental advantages is the substantial reduction in greenhouse gas emissions vs venting the pipeline. In the case of long, large diameter gas pipelines, this can prevent the potential discharge of thousands of tons of methane into the atmosphere.
Following the completion of the maintenance activities, a reinstatement leak-test of the replaced valve or pipework can be performed while the isolation is still in place. And provides an alternative to golden welds.
Real world examples will be discussed where double block inline isolation tools have facilitated pipeline modification, resulting in reduced project costs and production downtime, while minimising the discharge of emissions.
The utilization of in-line isolation tools not only enhances the efficiency and safety of pipeline repair and maintenance but also aligns with increasing demand to reduce emissions and create a more sustainable energy infrastructure for the future.
Challenges for this technology will also be discussed, including long distance deployments in gas pipelines where the tools must be stopped midline with suitable accuracy. Also, a high degree of confidence of pipeline condition (bore, wall thickness) is required before inline isolation tool pigging as the hard OD of the tools is close to the ID of the pipe and good information is sometimes difficult to obtain.
Brian Cooper1, Matthew Moshier2, John El-Hallal2, David Anstead3, Lance Wethey4
1HT Engineering, Inc., Grand Rapids, USA. 2TC Energy, Chicago, USA. 3BP, Chicago, USA. 4ROSEN, Houston, USA
This paper presents the lessons learned by the team that planned, designed, and managed a project to run gauge pigs and in-line inspection (ILI) tools through an idled pipeline. The runs covered the multiple piggable segments of a nitrogen-filled 450-mile liquid hydrocarbon product line in preparation for its return to service. Running ILI tools in lines previously in liquid service and subsequently filled with nitrogen presents challenges. This study provides insight into the pipeline system characteristics, including human factors, that must be addressed to achieve successful tool runs in nitrogen.
For this project, the team synthesized requirements from management, technical, and operations stakeholders, and developed an execution plan. During planning, the team built a numerical hydraulic model to calculate the nitrogen flow rates and pressures required to successfully run the pigs. The team worked with local operations personnel and the ILI vendor to develop detailed work procedures. During operations engineers worked on site tracking procedure completion and monitoring operating conditions. Two ILI runs failed to meet acceptance criteria, one due to abnormal ILI tool drive cup wear and one due to inadequate nitrogen control procedures. The team identified the problems and designed solutions. After each operation, the team captured lessons learned and updated subsequent procedures accordingly.
The execution plan provided the company’s management with confidence that the project could be completed safely. The numerical hydraulic model allowed the team to optimize nitrogen injection and release locations, plan injection and release operations, and verify that pressures and pig speeds could be kept within acceptable operating ranges. The solutions for the failed runs (a revised ILI tool drive cup design and a new procedure for nitrogen control) prevented recurrence of the problems and resulted in successful reruns. The lessons learned process allowed the team to improve its numerical model and human performance as the project progressed. By monitoring and analyzing the operating conditions in real time, the engineers were able to provide the project manager with the information and recommendations needed to run the operations safely and recognize emerging problems quickly.
Pipeline operators are frequently faced with the need to respond to changing market conditions and must be able to safely inspect idled lines in a timely manner. The results of this study provide operators with insight into the factors that must be addressed to achieve successful tool runs in nitrogen. These results complement the findings of Bonner, D., Greig, A., Lindner, H., Becker, J., Roulston, B., (2018, September 24-28). REACTIVATING A LEGACY PIPELINE – SIMULATING ILI RUN BEHAVIOR, OPERATION OPTIMIZATION, AND PROJECT CHALLENGES. International Pipeline Conference, Calgary, Alberta, Canada.
Kevin Spencer1, Phillip Bondurant2, Haraprasad Kannajosyula2, Jabin Reinhold3
1Quest Integrity, Calgary, Canada. 2Quest Integrity, Seattle, USA. 3Quest Integrity, Traverse City, USA
Small diameter pipeline crack in-line inspection (ILI) has typically been an underserved industry segment, primarily due to the difficulties associated with the physical limitations of packaging sensors, electronics and power sources within a small housing which is then able to successfully navigate challenging pipeline configurations. New ILI technologies are often therefore introduced for larger diameter tools and then miniaturized as far as possible. This paper presents the development, testing and implementation of an Electro-Magnetic Acoustic Transducer (EMAT) inspection vehicle specifically designed to detect and characterize longitudinal cracks in small diameter and difficult to inspect gas pipelines.
The paper will present the initial tool development and subsequent implementation on to a free-swimming bi-directional inspection vehicle. Since then, the tool has successfully and safely completed its initial inspections which provided critical information in the tool’s performance and further design improvements. Secondly the paper will present, via case studies, the tool’s performance in detecting and identifying axially orientated cracking anomalies through both full-scale testing and field validations. The case studies include comparisons with additional inspection data streams, providing an integrated approach to the identification of complex morphologies or interacting anomalies.
Rogelio Guajardo1, Eder Prestegui2, Träumner Katja3, Victor Haro3
1NDT Global Spain, Barcelona, Spain. 2NDT Global Mexico, Mexico City, Mexico. 3NDT Global Germany, Stutensee, Germany
ERW penetrators are a subtype of lack of fusions. They are planar anomalies located in the bonding line. What differentiates them is that they are short in length (<1.0in) but deep e.g., >50% of the pipe wall. The integrity risk of these anomalies is the possibility to leak instead of bursting.
Ultrasonic Shear Wave (UTCD) technologies are the recommended ILI choice to address planar/linear anomalies such as the lack of fusions and therefore the penetrators. However, the minimum probability of detection (POD) dimensions from the UTCD tools in the long seam are 1.0in x 0.079in (length x depth) placing the penetrators below performance specification. This raises the questions: 1- What options do we have to address these features? and 2- What are the capabilities from UTCD ILI inspections?
The goal of the paper is to provide a comprehensive evaluation of 1- UTCD tool settings and configuration, 2- UTCD measurement techniques pulse echo and pitch & catch, and 3- Analysis procedure updates required to identify and size these features which will allow the reader to understand the shear wave capabilities when selecting and ILI UTCD technology to address these features.
Key words: ILI inspection, UTCD, Lack of fusion, ERW weld, crack detection, UT technology, Seam weld, ILI application, ILI analysis
Laurie Knape
API, Houston, USA
In November 2022, API and the joint Pipeline SMS Industry Team published Pipeline SMS: A Contractor’s Guide to give pipeline contractors and service providers an enhanced understanding of how the scope of their safety programs should be integrated with an operator’s Pipeline SMS. A tool has been created with industry collaboration, showcasing 56 key requirements of API RP 1173: Pipeline Safety Management Systems, that will help operators and contractors integrate their safety efforts. In this presentation, we will show how the newly developed tool will help contractors and service providers mature internal safety programs that support Pipeline SMS. The tool is scalable based on the size of the organization and the scope of work and can be a valuable tool in starting the PSMS journey. In addition to reviewing the tool, we will highlight good practices seen from a pipeline operator and a service company on the value gained from the integration of their safety programs. API and the joint Pipeline SMS Industry Team have created a Contractor SMS Assessment pilot program. We will review the Contractor Assessment program’s step-by-step details and discuss deliverables, scoring, and benchmarking.
Corey Richards1, Thor-Staale Kristiansen2, John Nonemaker3, Alvaro Patino3, Borge Hamnes2, Oyvind Gravdal2
1ROSEN Group, Calgary, Canada. 2ROSEN Group, Bergen, Norway. 3ROSEN Group, Houston, USA
In response to pipeline restrictions that prevent the use of common free-swimming in-line inspection equipment, self-propelled inspection solutions have emerged as a transformative alternative. Leveraging robotics, automation, and advanced sensing, these solutions can autonomously navigate complex pipelines without the requirement for conventional access points or product flow. The adoption of self-propelled systems enables operators to conduct comprehensive inspections in pipelines previously considered inaccessible. This paper outlines the utilization of a self-propelled tether approach supported by case studies. The paper will outline in detail the workings of the inspection tool, particularly: the ridged ring UT sensor unit, the modifications and testing to ensure the system could pass features in the line, and the electrically driven propulsion system.
The first case study introduces a self-propelled robotic Ultrasonic Wall Measurement (UTWM) solution deployed in a 16”/20” pipeline. While the focus of this case study is the deployment of this inspection solution in the 20” section, it will also compare a previous operational attempt with running a free-swimming 16”/20” tool in this line. Overall, the case study will outline not only how this solution better ensured the integrity of the line itself, but also how its execution reduced operational requirements while still collecting high-quality in-line inspection (ILI) data.
Case Study two will address the challenge of offshore pipelines situated in remote and rugged terrains. This case study presents a tethered self-propelled inspection device equipped with ultrasonic sensors. What was of particular interest in the case study was the tool’s ability to navigate over 11 complex bends. The study showcases the device’s technical abilities in conducting real-time assessments and overcoming access limitations inherent in such locations. Further the case study will also cover the extensive testing required to safely complete such inspections.
Paige Chenevey1, Eric Bergeron2, Alexandre Thibault2
1Marathon Pipe Line, Findlay, OH, USA. 2Flyscan Systems, Quebec City, Canada
Since the end of 2022, Marathon Pipe Line has been using and testing Flyscan Systems’ remote sensing technology over their liquid pipeline Rights-of-Way (ROWs) to benchmark and validate the use of machine learning (ML) algorithms, photogrammetry and hyperspectral imaging to perform real-time threat detection, liquid leak detection of crude oil and refined products, and other advanced imaging features related to geo-hazards.
This paper will present scientific approaches used, and real-life results from 198 patrols between November 2022 and August 2023 which identified 2,594 threats across 35,706 miles of ROW from Alaska to Texas, including the Rockies and the Mid-west.
Examples will include, what is potentially the first ever detection of a diesel seeper leak, identified below computational pipeline monitoring system detection thresholds using a hyperspectral imaging system during routine aerial patrols. Other examples will include detection of contaminated soils from third party activity, detection of real encroachments and documentation of various types of objects and activities on the ROW of interest to pipeline operators. Finally, examples of new imaging capabilities will be presented, including detection of exposed pipes after serious weather events, vegetation analysis, and erosion monitoring.
Richard Mcnealy1, Vahid Ebrahimipour2, Duran Mendoza1, Praveen Kumar3
1Chevron, Houston, USA. 2Chevron, Malongo, Angola. 3Xaaslabs, Sunnyvale, USA
While many upstream pipelines and flowlines are piggable, their operating characteristics may render them not smart piggable because they cannot be practically cleaned or configured to enable successful conventional high resolution in-line inspections. Minimally intrusive sensors are now available to pipeline operators that manage in-line navigation risks while recording full length data used to understand the condition of the pipe wall equivalent to a hydrostatic integrity assessment and detecting leak points-of-interest (POIs). This paper presents the results from a pilot deployment of a multi sensor device comprised of large standoff passive magnetometer sensors coupled with acoustic, pressure and temperature sensing capability all integrated into the form factor of a minimally intrusive maintenance pig. An understanding of fundamental magnetic theory is applied to the sensor data to characterize the interaction of a ferro magnetic body, i.e., steel line pipe, within a native magnetic field to conclude relative changes in the mass or changes in pipe wall thickness along the full length of the pipeline. The pilot also illustrates a method that leverages multiple sensor datasets using 1st principles equations to calculate various parameters for characterizing leak location and severity. Comparison of fundamental magnetic, acoustic and temperature quantities, measured by the sensors, with physical pipe wall truth data illustrates the basis for models developed to conclude pipe wall condition and integrity management actions consistent with equivalent understanding derived from a hydrostatic integrity assessment and effective loss of containment risk management using cloud-based software applications.
Anthony Tindall1, Steve Farnie1, Jeff Sutherland2, Stuart Clouston2
1Baker Hughes, Cramlington, UK. 2Baker Hughes, Calgary, Canada
It is well known that when corrosion pits interact, the interpretation of inspection data gathered by Magnetic Flux leakage tools (an indirect measurement technique) becomes challenging due to the nature of the overlapping and superimposing signal responses across the multi-defect profiles. Such “complex” corrosion is of particular concern to pipeline operators as it is these areas, particularly axially oriented, that are often the most critical to pipeline integrity. And then, being the most difficult to both interpret and size accurately, these can lead to “outliers” relative to conventional ILI specifications and industry guidelines (e.g. API 1163). Such outliers are increasingly grouped into two types, namely Safety Outliers (where defect severity is under called leading to underestimated remaining strength) or Resource Outliers (when defect severity is overcalled potentially leading to unnecessary digs).
The goal of any in-line inspection method is to represent corrosion fully and accurately on the pipe. To achieve best performance, we must be able to first detect when these complex or interacting signals occur and then, more importantly, interpret them correctly. In physics terms, the nature of MFL field leakage is a 3-dimensional vector and predictable, yet different signal responses to metal loss (and other features) are observed in each of these 3 vectors which can be quantified and characterized as an improved means to translate leakage signals to the corrosion they more accurately represent.
Single axis MFL, whether conducted with axially or circumferentially oriented magnetizers, will reach limits in its capabilities regardless of sensing resolution. MFL is a mature technology, and an operator today should expect most tools to perform to specification on isolated corrosion. However, the adoption of long proven Triaxial sensors, at optimal resolution, on Magnetic Flux Leakage inspection vehicles provides an integrity engineer significant advantages to minimize potential outliers when things are not so straight forward.
This paper will outline how the three independent components of the triaxial flux leakage response provide unique identifiers for cases of axial corrosion, highly asymmetrical defects, corrosion in corrosion, wide area erosion/corrosion with pitting, to name but a few. At the same time, the additional signal components provide independent measures that enable better performance in latest generation algorithm techniques and development than those trained on fewer inputs.
The authors will present real world examples of these unique identifiers being used in practice to interpret highly complex corrosion and the latest work Baker Hughes has been conducting in close partnership with our customers with the common goal to best manage these “complex morphologies” successfully and efficiently with one inspection.
Emmanuel Valencia, Atul Ganpatye
ADV Integrity, Inc., Magnolia, USA
Traditional dent assessments involve calculating deformation strains and stress concentration factors (SCF) as proxies for the severity of the dent. Typically, the determination of SCF requires advanced computational methods (like finite element analysis) with specialized software and skillsets. This can be time-consuming and subjective, greatly depending on the engineer’s skill level using the approach.
Of the two factors described above, deformation strain calculations have been well-established and definitive because strains can be directly and readily interpreted from the deformation geometry. Therefore, this paper only focuses on the SCF aspect where the proposed approach, using machine learning (ML), can significantly reduce the efforts and resources needed to determine the SCF.
Due to the non-linear relationship of the dent shapes and their corresponding SCF values, multiple deep learning ML methods were considered in this study. The final model architecture involved Convolutional Neural Networks (CNN) due to their ability to extract features, group objects, and discover valuable data patterns from unknown elements.
The CNN model was trained on 4,667 raw ILI data files containing dent shapes which underwent significant preprocessing, such as data normalization, filtering, and smoothing. The final model was selected after careful fine-tuning of the hyperparameters and comparison of 180 CNN model variations where it successfully predicted SCFs ranging from 1.04 to 10.69 with a root mean squared error (RMSE) of 0.418 and a coefficient of determination (R2) of 0.929, indicating a high level of accuracy and goodness of fit, respectively.
Although the results are favorable, the training dataset is biased toward a single pipeline operator and therefore does not represent the global statistics of dented pipelines. Along these lines, the paper discusses ideas and proposals for a more robust implementation of the approach for wider applications. The work demonstrates that the model has the potential to serve as an assessment tool to provide immediate, in-the-ditch guidance to pipeline operators, therefore reducing downtime and limiting resources.
Zain Al-Hassani1, Simon Slater2, Chris Davies3
1TC Energy, Houston, USA. 2ROSEN, Columbus, USA. 3ROSEN, Houston, USA
Gas transmission operators are now required by regulation to reconfirm the MAOP of pipelines lacking traceable, verifiable, and complete (TVC) pressure test records. TC Energy operates a 20” natural gas transmission pipeline in Northern Ohio, which has 54 individual segments that meet the requirements of a covered segment as per §192.624 (a)(1). TC Energy performed an Engineering Critical Assessment (ECA) of the pipeline to reconfirm the MAOP. The foundation of the ECA was a full suite of in-line inspection (ILI) technologies to detect, identify and size the anomalies that remain in the covered segments. This included ILI technologies capable of detecting crack-like anomalies, selective seam weld corrosion, and hard spots. ILI was also used to measure material properties and attributes when these were not known. Using the material data together with other data sets, the different populations of pipes within the covered segments were identified. TC Energy used this full suite ILI approach for ECA as pilot project. As such, a pressure test was also performed to confirm the applicability of the ECA approach. The ultimate aim of the exercise was to compare the two methods holistically across one example line to help develop a better understanding of which method should be used and when. This paper provides a walk-through of the ECA process performed by TC Energy and ROSEN. It provides a description of the documentation and specific content required by §192.632. It is intended to provide operators with an example of how an ECA is performed and highlight some of the critical aspects that have to be considered.
Jeff Sutherland, Melissa Gurney
Baker Hughes, Calgary, Canada
Since the introduction and validation of ILI Magnetic Flux Leakage (MFL) specifications for pinhole corrosion defects more than 10 years ago, industry has benefited greatly with gained experience with such capabilities.
This paper provides a brief review of the nature of “pinhole” ILI performance particularly for MFL inspection including the influences in providing accurate inspection results, as well as technical development steps to date regarding pipeline corrosion inspection and reporting.
The interpretation of API 1163 guidance has played a role in such perceptions and specifications that will be outlined in this paper. Similarly, the nature of “hard boundaries” behavior related to corrosion type categories (the “POF (Pipeline Operators Forum) categories”) plays a role. The need to address such perceptions will be described and real examples of features will be presented with case examples of isolated and complex corrosion morphologies.
Industry feedback, both in the field measurement improvements and volume of feedback features, has led to further improvements and possibilities beyond current ILI conventions.
The paper will then describe with examples of alternatives and with some description of new conventions of ILI performance for the future.
Michael Byington1, Facundo Nahuel Ignacio Lamas2, Rodolfo Eduardo Rodríguez2, Celeste Vera2
1INGU, Houston, USA. 2Pan American Energy, Cerro Dragón, Argentina
The development of conventional inline inspection technology has been geared towards ultra-high resolution tools requiring a completely cleaned pipeline and coming with increasing costs and data handling time. By comparing data between inspections, unconventional inline inspection tools equipped with off-the-shelf micro-electromechanical magnetometers provide actionable information on the best allocation of resources for digs and high resolutions tools as well as the location of unexpected changes such as illegal hot tap installations. To ensure an accurate comparison between inspections, the data of subsequent inspections must be perfectly aligned. This presentation will discuss a fully automated approach to align inspection data using Monte-Carlo based time warping strategies.
We will illustrate the method with a case study conducted by Pan American Energy. They installed a hot tap at an undisclosed location along a nearly 3,000-meter steel pipeline and asked INGU to locate it. The hot tap was unambiguously identified and Pan American Energy confirmed that the provided location was within the 6 meter acceptance criterion for the project.
KEYWORD(S) FOR SUBJECT AREA: ILI Analysis; Emerging issues, technology; Unpiggable Inspections and Technology
Amir Behbahanian1, Adrian Belanger2, Robert Coleman1, Paul Dalfonso1, Ron Lundstrom1
1T. D. Williamson, Salt Lake City, USA. 2T. D. Williamson, Houston, USA
Machine learning tools have been used for over a decade to process the large amounts of in-line Inspection (ILI) data and to report accurate sizing of metal loss features. With the explosion of software solutions that came with the advancement of graphic processing units, (GPU) power and memory available to the commercial market, the use of machine learning in processing magnetic flux leakage (MFL) tools for corrosion sizing now standard in the industry. An aspect of automation that does not get as much attention is the identification of features such as fixtures. Traditionally this task has been done either manually or with a semi-automated process based on signal pattern recognition by utilizing operator provided survey data. As fixtures are commonly used as a reference point when performing dig verifications, fast and effective methods for locating them are helpful.
This paper will present an approach using a machine learning method called semantic segmentation. There is an enormous amount of information contained in an MFL survey that has an image like structure with magnetic measurements sampled both axially and circumferentially on a grid. The powerful technique of semantic image segmentation, which is used in applications like autonomous driving, medical imaging, urban planning, manufacturing, robotics, etc., is ideal for analyzing this data.
Four different models will be presented to demonstrate how a combination of them can perform the task of identifying and classifying pipeline features. This work will lay the foundation of not only automating a semi-manual task but training models to focus on features of concern to the operator. Due to concerns about aging infrastructure, identifying certain types of fixtures can help with integrity threat management. The use of these models has the potential of identifying specific features that have known integrity concerns and facilitate a pipeline owner’s remediation plan.
Michael Turnquist1, Yohann Miglis2, Yanping Li3
1Quest Integrity, Boulder, USA. 2Kinder Morgan, Colorado Springs, USA. 3Enbridge, Edmonton, Canada
A critical factor in determining the remaining strength of a corrosion feature intersecting a longitudinal seam weld (LSW) is whether the corrosion is preferential to the weld (often referred to as selective seam weld corrosion or SSWC) or coincident with weld yet no preferential attack of the bondline is occurring. SSWC is a form of corrosion that most often occurs in the bondline of electric resistance welded (ERW) and electric flash welded (EFW) pipe and typically has the appearance of a V-shaped groove. Past research supports that if no preferential attack of the LSW bondline is occurring and the weld has adequate ductility, the presence of the LSW does not reduce the remaining strength of the feature when compared to features not intersecting the LSW, and that industry accepted corrosion assessment models are suitable.
This paper provides an overview of additional full-scale destructive testing and detailed engineering analysis that further supports the observation that under most realistic conditions, the presence of a LSW does not negatively impact the remaining strength of corrosion feature. Potential exceptions to this behavior are related to the ductility of the weld, the constraint effects and morphology from the feature geometry, the operating stress of the pipe, and whether or not preferential attack of the LSW bondline is occurring.
The work presented in this paper is part of the Pipeline Research Council International (PRCI) project EC-02-13 “Response to Corrosion Interacting with the Longitudinal Seam in Liquid Pipelines”. The objectives of this project are to clarify which analysis methodologies are appropriate to assess corrosion coincident with a pipeline LSW and to support the development of recommended guidelines to effectively manage these types of features. This work is being executed in parallel with sibling projects EC-02-12 “Evaluation of Selective Seam Weld Corrosion Susceptibility”, NDE-4-13 “Selective Seam Weld Corrosion Detection with In-line Inspection Technologies”, IM-3-03 “Comprehensive Review and Assessment Guidelines for SSWC”, and IM-1-08 “Pragmatic Application of MegaRule RIN 1 – 192.712 Toughness Values”
Brian Leis1, Amin Eshraghi2
1Consultant, Worthington, USA. 2Acuren, Calgary, Canada
API’s release of the first edition of its Recommended Practice (RP) 1183 titled “Assessment and Management of Pipeline Dents” in November 2020, and Errata 1 a few months thereafter, marked the culmination of 14 plus years of related work. Against that backdrop, the PRCI, in collaboration with the PHMSA initiated Project MD-5-1, which sought to assess that activity, to identify technology gaps and aspects of that work that could enhance the RP, or broaden its capabilities. Concurrently, PRCI in collaboration with PHMSA initiated Project MD-5-2 seeking to enhance the tools being adopted in the RP. Aspects of these developments were evaluated rather critically at PPIM2023 in a paper that discussed what it termed “enhancement of indentation crack formation strain estimation” in PRCI’s reporting MD-5-2. Independently, about the same time a four-part series of papers was being planned with a similar but much broader intent and complexity, which is now in part in print in a refereed journal. This paper is the practical synthesis of that breadth and complexity, distilled with guidance and with takeaways concerning the issues and limitations of the current RP 1183.
This paper identifies many of the key assumptions latent in the Level 1 and Level 2 practices of API RP 1183, and truth-tests them by comparison with results generated using full-scale-validated Level 3 analyses. Where issues emerged with those assumptions, guidance and takeaways are presented to help mitigate their practical implications. Results for smooth single-peak symmetric and asymmetric dents formed in geometrically stiff versus compliant pipes over a range of depths from less than 1% OD up to 10% OD are considered. It is shown that the Level 1 and 2 practices can be effective for shallow large-radius single-peak dents, as might be formed by smooth rounded field boulders. However, the viability of those Level 1 and 2 practices diminishes as the dent depth and its curvature increase — with major issues emerging at depths as shallow as 1% OD when dealing with smooth flatter asymmetric dents. The RP’s concept of dent ‘restraint’ was truth tested and found problematic at dent depths typical of the shallower populations typically evident in many ILI surveys. The results discussed show that the Level 2 practices of API RP 1183 can underpredict the severity of smooth asymmetric dents by in excess of 100%. Finally, the RP’s provisions when dealing with skewed-dents have been truth-tested. For the cases considered it was evident that the peak strain was dictated by the shape of the contact, far more so than by the skew-angle. Because this outcome will be dependent on the shape and size of the dent formed, even low skew-angle dents likely should be evaluated at Level 3. Guidance and takeaways are provided to help manage skewed and other single-peak dents, whereas multipeak dents and those near possibly interacting features are deferred.
Jason Weiss1, Brett McNabb2, Alisdair Blackley1
1Argus, Edmonton, Canada. 2Apache Pipeline Products, Edmonton, Canada
The efficient and safe transportation of fluids through pipelines has been a cornerstone of modern infrastructure for decades. However, pipeline operators often face challenges when it comes to inspection, maintenance, and cleaning. These challenges are often addressed through pigging programs, however a large portion of existing pipelines are considered “unpiggable”. This is primarily due to pipeline size, complex geometry, or unique operational conditions. In recent years, the need to maintain and ensure the integrity of all types of pipelines, including those previously considered unpiggable, has grown significantly. The paper begins by defining what makes a pipeline “unpiggable” and delves into the common reasons for this classification. It will then explore the challenges associated with pigging previously unpiggable pipelines and some innovative solutions for pigging this type of infrastructure.
One of the primary challenges in pigging unpiggable pipelines is the development of suitable pigs and technologies. Traditional pigs are often designed for pipelines with standard dimensions and features. The paper discusses how the industry has responded to this challenge through the development of specialized pigs tailored to the unique requirements of unpiggable pipelines. This includes a summary on the development of various cleaning and product recovery solutions, such as foam pigs and swabbing devices, designed to address the unique challenges posed by unpiggable pipelines. Additionally, the paper includes information on the use of small, single body inspection tools that have been developed by industry to allow for in-line inspection in these applications.
Another large challenge surrounds the changes required to update and modify existing pipelines to include the necessary pig launching and receiving infrastructure and remove or update features that hamper successful pig runs. The paper highlights the challenges associated with collection of data on existing historical pipelines, along with some of the changes required to ensure successful pigging operations. Specifically, the paper outlines how the use of pipeline Pigging Valves and Multi-Pig Launchers can be used as an innovative alternative to traditional barrel-style pig launchers or receivers in previously unpiggable applications.
In addition to technological advancements, the paper delves into the operational, regulatory, and environmental considerations faced during pigging activities in unpiggable pipelines. These challenges include access to the pipeline, transportation and deployment of pigging equipment, high frequency pigging, emissions regulations, and safety considerations.
In conclusion, the pigging of previously unpiggable pipelines presents a compelling challenge that demands innovative solutions. This paper provides an overview of the challenges faced and the technological advancements, operational strategies, regulatory compliance, and economic factors that must be considered. By understanding these complexities, pipeline operators and industry professionals can make informed decisions and effectively address the unique requirements of pigging previously unpiggable pipelines, ensuring the continued safe and efficient transportation of vital fluids in our modern infrastructure.
Pablo Cazenave1, Sergio Limón1, Ravi Krishnamurthy1
1Blade Energy Partners, Houston, USA
An onshore/offshore pipeline in South America transporting brine solution experienced a failure initially attributed to external circumferential cracking in an onshore section of the pipeline. The failed pipeline rested above ground in a concrete ditch exposed to ambient conditions. Field assessments and land surveys of the failed site indicated possible nearby land movement.
This paper outlines the work conducted to review the Failure Analysis results, the aggregation of historic and recent in-line inspections (geometry + inertial + axial MFL), above-ground land movement survey data, and the identification of the cause of the circumferential cracking for the development of a short- and long-term remedial plan to address the effects on land movement on the integrity the pipeline.
Kathrin Schroeer1, Andrew Wilde2, Morry Bankehsaz3
1ROSEN Technology & Research Center, Lingen, Germany, 2ROSEN UK, Newcastle, UK, 3ROSEN USA, Houston, USA
Increases in pipe diameter, either in the form of localized bulges or expansions that affect the entire pipe circumference are reported infrequently by in-line inspections but they can indicate issues relating to the pipe manufacturing, construction or commissioning process that could compromise the future integrity of the pipeline. Typically diameter changes are small and below the detection and / or reporting threshold of high resolution caliper tools. However, as noted within PHMSA advisory notice ADB–09–01, pipe expansions can be indicative of material property deviations, including yield strengths that are significantly below specified minimum requirements, and can pose a credible threat to the integrity of a pipeline. Consequently, it is important that such anomalies are reliably detected and sized and that their severity is assessed appropriately.
This paper provides a summary of ROSEN’s experience of detecting pipe expansions and bulges including a review of typical anomaly characteristics and discussion on the capabilities of ILI tools to detect and size them. The potential causes of ID increases are reviewed and a phased integrity assessment approach is provided using a recent example of a pipe expansion identified in a pipeline in Canada. Finally, possible issues relating to the coincidence of pipeline expansions with other forms of pipeline damage including environmental cracking, corrosion and geometric anomalies are considered.
David Scharff1,Dr. Kaushik Parmar1, Adrian Banica1
1Direct-C, Edmonton, Canada
Underground vaults are employed along pipelines to accommodate pumping and shut-off systems that require a large volume of space around the pipeline. Within each vault a number of flanges, valves, and other potential leak points are present. Monitoring vaults for leaks presents numerous challenges: a) aerial surveys are not an option, b) they are often in remote locations, c) they are prone to flooding due to rain and snow run-off. This paper describes the development of an Industrial Internet of Things (IIoT) vault monitoring system that detects an unexpected release of liquid hydrocarbons within the vault and monitors the presence and level of water. A case study on the deployment and operation of this new multifunctional system in underground vaults at multiple northern locations is described. Ground movement monitoring is currently under development as an additional monitoring capability within the same IIoT system and some initial trial data will be presented.
Chris Alexander1, Tony Rizk2, Rodney Clayton2, Ahmed Hassanin1, Josh Wilson3
1ADV Integrity, Inc., MAGNOLIA, USA. 2Boardwalk Pipelines, Houston, USA. 3Allan Edwards, Tulsa, USA
ABSTRACT
Composite materials are commonly used in the reinforcement of hoop-oriented defects such as corrosion, dents, seam-weld anomalies, and gouges within pipelines. Additionally, they can be designed to reinforce features susceptible to cracking when subjected to bending and tension loading, including girth welds and wrinkle bends. Of particular interest, given historical failure patterns, is when wrinkle bends are subjected to high strain-low cycle fatigue loads.
This paper presents results and findings of a study that involved full-scale testing of wrinkle bends. The test program encompassed three distinct tests on 26-inch x 0.281-inch, Grade X52 pipes, all of which had wrinkles removed from service. The test program comprised testing an unreinforced wrinkle bend sample, as well as two additional samples that were reinforced with custom-designed E-glass-epoxy and carbon-epoxy composite technologies with axial-dominant fiber architectures.
In the case of the unreinforced wrinkle sample, the maximum recorded axial strains in the wrinkle feature were +/- 1%, in which the sample failed after 107 bending cycles. The two composite reinforced samples utilizing the E-glass-epoxy and carbon-epoxy technologies failed after 1,774 and 863 bending cycles, respectively. These results demonstrate that both systems were able to increase the life of the unreinforced wrinkle sample by as much as 16 times.
From an operational standpoint, these findings imply that the service life of existing wrinkle bends could be substantially prolonged, potentially by decades, assuming that such bends are subjected to loads of similar magnitude 5-10 times per year, as examined in this study. This research offers valuable insights into the transformative role of composite materials in enhancing the longevity and durability of wrinkle bends in pipelines.
David Futch¹
¹ADV Integrity, Inc., Magnolia, USA
ABSTRACT
Type B sleeves are a proven repair technique and are typically installed tight fitting with the ends fully welded. The sleeves are configured in a way to allow for load sharing from the carrier pipe to the sleeve and provides pressure containment when/if the underlying carrier pipe leaks. Once a leak occurs, the annulus space becomes pressurized which increases the stress on the side seams and fillet welds. Prior research has shown a resulting finite life of the sleeve as those welds can leak after some period based upon cyclic internal pressure loading and weld quality.
The use of filler material applied to the carrier pipe prior to applying the Type B sleeve is a common practice to increase load transfer, however, not required by any code and standard as the sleeve is pressure containing. While seemingly straightforward, the inconsistent application of filler material could result in unexpected results. This study examined and attempted to standardize the application of filler material, both locally applied and when the annulus space is pumped using a commercially available grout material.
The test program consisted of the repair of longitudinal seam weld features repaired by various sleeve configurations. These configurations included one installed without fill, with a locally applied fill, and a grouted annulus space. Each sample was repaired and cycled (until runout of 100,000 cycles). The grouted sample was the only to achieve runout reaching 100,000 cycles, 20x more cycles than any other sample. Metallurgical examination confirmed little, if any, growth occurred after repair, indicating the most advantageous load transfer and repair life.
Peter Martin1, Nathan Switzner1, Joel Anderson1, Joshua Stuckner2, Owen Lopez-Oneal3, Sophia Curiel3, Peter Veloo3
1RSI Pipeline Solutions, New Albany, USA. 2NASA, Cleveland, USA. 3Pacific Gas and Electric, Oakland, USA
ABSTRACT
Pipeline operators in the United States are increasingly relying upon materials verification programs (MVP) to establish the properties of pipelines lacking reliable records. The ongoing MVP at the Pacific Gas and Electric Company (PG&E) applies external nondestructive testing (NDT) to exposed line pipe to gain insight into the grade, vintage, and manufacturing method of the pipe. PG&E supplements the standard NDT methods for composition, strength, and geometry with the nondestructive collection of surface microstructures using metallographic replicas. The microstructures are quantitatively evaluated for ferrite grain size and fraction of pearlite. These are then used in conjunction with other measured characteristics to support determination of grade and vintage, and to identify populations of similar pipes. Automating these analyses is of interest because the manual evaluations are labor intensive and subject to variability associated with evaluator skill, judgement, and fatigue.
Traditional methods for automating microstructure analyses are often challenged by small variations in sample or image quality. Machine learning (ML) models have been shown to be more robust, but training these models typically requires hundreds of manually pre-processed images. This creates a high initial investment that impedes practical implementation in an operational environment. Recently, pre-training ML models on a large number of generic images has been shown to substantially reduce the required number of application-specific training images.
This work will describe the performance of an open-source ML model pre-trained on a database of over 105 microscopy images and subsequently trained on fewer than 20 line pipe microstructures. The training and validation of the model will be presented, along with a comparison of ML and manual evaluations of more than 150 microstructures from more than 50 line pipes. The results will show the performance of the ML model to be comparable to that of manual evaluations.
Joel Anderson
RSI Pipeline Solutions, Oklahoma CIty, USA
ABSTRACT
The regulations published by PHMSA in October of 2019 require non-destructive examination (NDE) to determine the material properties of pipelines that lack traceable, verifiable, and complete (TVC) records. To meet this requirement, operators must conduct verification of pipeline material properties in accordance with 49 CFR 192.607. Inherent in these requirements are requirements to achieve a 95% confidence level and the use of “statistically valid basis”. But absent in the regulations is how to determine if this has been met. Consequently, this leads to uncertainty on the part of the operators if they’ve done enough and are the observed differences indicate that the samples truly are different.
Differences will always exist between the measured value and the true value since perfect measurements are impossible. Errors of varying magnitude will always exist due to random effects from any number of sources. The inevitable question arises is whether these observed differences are enough to be significant and have enough samples been completed to be able to tell the difference.
This paper will discuss how to set up a sampling plan to meet the necessary goals. Including how to determine if a sample is inconsistent with some value, determining sample size and comparing two samples.
Avenida Central Garage rates
Avenida South Garage rates
Kelly Thompson¹
¹Williams, Tulsa, USA
Hard spots are a pipeline defect created during original manufacturing. These are typically considered stable unless acted upon by coincident environmental factors including coating degradation, atomic hydrogen, and stress. As a result of industry lessons learned and recent hard spot related failures on its system, Williams is executing a hard spot mitigation program that encompasses improvements to our risk assessment model to account for hard spot defects. In this presentation, we will share how we are incorporating this risk into our modeling approach and how those results influence the mitigation effort. Additionally, this presentation will discuss the benefits that can be realized through broader industry collaboration, current collaborative studies underway, and key metrics to advance industry understanding of the hard spot risk that ultimately will improve overall pipeline safety.
Scott Olson¹, Andy Studman², Jim Evans³, Aidan O’Donoghue⁴
¹Shell Trading & Supply Operations, Trinidad & Tobago, ²Shell International Ltd, Aberdeen, UK, ³Pigtek Limited, Temple Normanton, UK, ⁴Pipeline Research Limited, Glasgow, UK
Abstract
A routine sphering operation to control liquid hold up on a 30-inch trunk pipeline transporting wet gas was interrupted when a sphere became damaged and stalled in the pipeline following interaction with a subsea isolation valve inadvertently stuck in the partially closed position. Rectifying the valve to the fully open position followed by rescue pigging was selected as the remediation strategy. The offshore platform topsides facilities however were only designed to launch spheres, through the side branch of an unbarred tee and included a 30-inch to 36-inch reducer and 1.5D bend. The rescue pig required careful selection and onshore pigging trials were undertaken resulting in extensive modifications to the rescue pig design and set up to demonstrate the rescue pig could successfully traverse all the features in the topsides pipework. Following a successful subsea campaign to fully open the subsea valve, the rescue pig was deployed and successfully recovered the damaged sphere from the pipeline. This paper and associated presentation describes the details of the various challenges and solutions that enabled a safe and successful rescue pigging operation.
Chris Alexander1, Aquiles Perez2, Casey Whalen3
1ADV Integrity, Magnolia, USA. 2ECA Solutions, Houston, USA. 3CSNRI, Houston, USA
Over the past 30 years composite repair technologies have changed the landscape of pipeline rehabilitation and are used to reinforce a wide range of defects including corrosion, cracks, dents, and vintage girth welds. Composite crack arrestors have also played a role in this time period, although their use in this capacity has not been as widespread as their role in structurally reinforcing pipelines as part of integrity management programs. Interestingly, the Clock Spring technology was originally developed as a crack arrestor; however, the pipeline industry was able to conceive alternative uses for composite reinforcing technologies that spawned one of the fasting growing technology applications in the pipeline industry.
Composite crack arrestors have been proven to effectively arrest brittle and ductile running fractures, primarily focused on high pressure gas transmission pipeline systems. This has been validated via full-scale testing on high-energy pipe. For the most part there has been little design guidance provided to the pipeline industry for how a composite crack arrestor should be designed. The approach employed by most researchers has been to design and install a robust arrestor and then conduct testing to experimentally validate its ability to arrest running fractures. The composite crack arrestor design is considered a “success” if it stops the running fracture. Although the science behind modeling fracture is well understood, gaps exist in terms of how to arrest running fractures using composite materials using a well-thought-out design process. Methodologies have established a “qualified” approach rather than a “quantified” approach for design. This paper presents a framework for using composite materials as crack arrestors to arrest running fractures in CO2 pipelines that will be useful for pipeline companies seeking to build new pipeline systems or convert existing assets to CO2 service.
Daryl Bandstra1, Alex Fraser1, Miaad Safari2, Kai Ji2
1Integral Engineering, Edmonton, Canada. 2Enbridge Gas, Toronto, Canada
The transmission pipeline industry is increasingly utilizing probabilistic models for assessing the probability of failure of anomalies measured during in-line inspections such as corrosion and cracks. PHMSA (Pipeline and Hazardous Materials Safety Administration) has recently classified probabilistic models as best practice, suitable for supporting all types of decision-making, as these models effectively represent the uncertainty in input data using probabilistic distributions. When modeling corrosion using a probabilistic model, the in-line inspection data includes measurements of individual corrosion anomalies. When these anomalies are in close proximity, there is potential for interactions that reduce the overall burst capacity, and the effect of these interactions can be considered by modelling these individual defects as a cluster.
Some probabilistic analyses idealize the clusters as single, large anomalies while others address the added complexity of considering all possible combinations of the individual anomalies that comprise the cluster. This presentation will investigate the differences in the estimated probability of failure of these two approaches by evaluating a range of test cases and real-world clusters. These cases will illustrate scenarios where significant discrepancies exist and areas where both approaches yield comparable results. Additionally, we compare the effects of different approaches for modeling the correlation of measurement errors associated with anomalies within a cluster.
Carlos Madera1, Sean Knight2, Austin Guerrero2, Simon Slater3
1Dow Chemical, Houston, USA. 2ROSEN Group, Houston, USA. 3ROSEN Group, Columbus, USA
With the passage of §192.607 and PHMSA’s subsequent responses in FAQ’s 21 and 22, ILI is an approved method for measuring properties and delineating pipe into populations with similar characteristics. In cases where material properties remain unknown, ILI populations can be leveraged to optimize decision making and test locations to close out material property verification. To enable this, the process must achieve the required confidence without necessarily having to test one sample per mile, which is defined as the default in regulation. §192.607(e)(5) states that an alternative statistical sampling approach can be used if it can “achieve at least a 95% confidence level that material properties used in the operation and maintenance of the pipeline are valid.” This paper will provide details on two alternative sampling approaches that have been approved for use by PHMSA on Dow Chemical’s 8” Mossville to Kaplan line segment. The approaches are based on a combination of ILI and test data using statistical analysis to satisfy the 95% confidence level. The efficacy of these approaches will be demonstrated using the assessment program performed by Dow Chemical to define the status of existing material properties and produce a plan to close out unverified material property values and fulfill the requirements of §192.607. The discussion will provide specifics of the approaches used by Dow Chemical, including the scope of documentation required to support its implementation and acceptance by the regulator.
Bernardo Cuervo
EN Engineering, Houston, USA
As in-line inspection (ILI) yields the highest-per-mile discovery of anomalies, running cleaning pigs and ILI tools are an important part of most integrity management programs. However, not without their risks. On June 28, 2021, a natural gas explosion occurred after workers inserted a gauge plate in a launcher trap as part of a routine pigging activity. The explosion went through the open launcher enclosure, ejecting the pig from the barrel, injuring two workers and killing two more. On November 15, 2021, PHMSA published the Final Rule: Safety of Gas Gathering Pipelines (86 FR 63266). With this rule, more than 400,000 additional miles of gas gathering pipelines are now covered by Federal reporting requirements. Proactive operators are beginning to ascertain the ILI feasibility of thousands of miles of gathering pipelines for future ILI. Many of these pipeline operators are beginning to audit and review their pigging procedures to prevent catastrophic incidents. This paper describes the entire process from the perspective of a pipeline operator; including the experiences of maintenance personnel, and the challenges faced by field operations during the implementation and use of a new methodology.
Atul Ganpatye1, Chris Alexander1, Rodney Clayton2, Tony Rizk2
1ADV Integrity, Inc., Magnolia, USA. 2Boardwalk Pipelines, LP, Houston, USA
Traditional code-based approaches for assessing crack-like flaws in pipelines rely on several idealizations/assumptions regarding flaw shape and orientation, material properties, and applicability of the analytical framework used to estimate pipe performance. The uncertainties in these assumptions often result in an underestimation of pipe performance in terms of failure pressure prediction. Full-scale tests with pipe containing crack-like flaws have shown that the actual failure/burst pressures can be as high as 50% over the predicted failure pressure. This paper outlines an experimental approach to quantify the “effective” fracture resistance for crack-like flaws as it correlates to the results from full-scale testing. Using effective fracture resistance for failure pressure prediction is discussed as an alternative approach to providing better alignment with observed failure pressure data.
The study included full-scale burst testing of 12 samples of 26-inch OD x 0.281-inch wall, Grade X52 pipe, and four samples of 30-inch OD x 0.299-inch wall, Grade X60 pipe, containing crack-like features. Cracks were generated in the base pipe having depths ranging from 20.9% to 69.0% of the pipe’s nominal wall thickness. On average, experimental results showed that the actual failure pressures were between 20% and 40% higher than those predicted using analytical assessment methods. Analytical assessment was performed using three different fracture models: Modified Ln-Sec, MAT-8, and API 579. The paper discusses the interpretation of the discrepancy between the predicted and observed results in terms of effective fracture resistance of the pipe. This resistance is explored as a manifestation of lower crack tip constraint in a full-scale pipe-geometry sample, compared to traditional measures of fracture toughness using sub-scale specimens. Results are also discussed from a practical perspective of the potential reduction in the number of digs based on reinterpretation of failure pressure ratios using the effective fracture resistance.
The study results have the potential to provide a more robust predictive capability for estimating burst pressures of pipes containing crack-like flaws. Using the reinterpreted effective fracture resistance based on actual test data allows a systemic incorporation of almost every single detail in the pipe performance “system” – in this context, the “system” is the collection of all parameters/factors that directly or indirectly influence the pipe performance, such as: pipe properties, flaw morphology, stress intensity due to the presence of the feature, etc. Improved confidence in the predicted pipe performance using full-scale test data has the potential to meaningfully impact integrity management approaches by reducing the number of digs that may be flagged when using the traditional approach.
Pablo Cazenave, Ming Gao, Katina Jimenez, Ravi Krishnamurthy
Blade Energy Partners, Houston, USA
The possibility of hydrogen-induced cracking and hydrogen-assisted cracking as interactive threats is increasingly becoming a safety concern to pipelines. While few cases exist of fully documented onshore transmission pipeline failures due to CP-related hydrogen-assisted cracking, the possibility of hydrogen-assisted failures needs further investigation, particularly hydrogen interacting with stress corrosion cracking in corrosion potentials more negative than -850 mV CSE.
This paper presents a case study of a 22-inch onshore natural gas transmission pipeline that experienced in-service leaks and a rupture associated with axially and circumferentially oriented crack colonies initially thought to be traditional stress corrosion cracking. In-depth metallographic examination revealed cracking fracture paths consistent with hydrogen-assisted cracking. Further investigation of potential sources of hydrogen concluded that the source is the impressed-current cathodic protection system operated for decades at near the P/S potentials of −1200 mV CSE.
An approach to mitigating the threat of hydrogen-induced cracking in onshore pipelines is also outlined.
Frank Micheli1, Ken Maxfield2, Phil Tisovec2
1Bridger Pipeline, Casper, USA. 2KMAX Inspection, Millcreek, USA
Bridger Pipeline operates a crude oil gathering system, of approximately 3500 miles, in the Williston Basin of western North Dakota, eastern Montana and the Powder River Basin of Wyoming in the USA. The Bridger system contains many small diameter (3” to 6”) gathering lines that are a challenge to inspect with ILI tools. These challenges include low flow conditions, line cleanliness and paraffin build up. Many are first time inspections of pipelines with limited or unknown records, trap configurations, and fittings such as heavy wall tees and elbows. Also of concern are weather constraints with the seasonality of ILI inspection projects for pipeline repair and access. This paper presents how these challenges are addressed to successfully run ILI to comply with Bridger’s integrity management program.
Ali Ebrahimi1, Arash Mosaiebian2, Amir Ahmadipur1
1Geosyntec Consultants, Inc., Houston, USA. 2Enbridge, Inc., Calgary, Canada
Pipelines are linear structures that cross various slope geometries and geologies and are susceptible to geohazards such as landslides. The ground movements from the landslides can potentially induce axial, bending, and torsional stresses in pipelines. Inertial Measurement Unit (IMU) bending strain data are commonly used for assessing the pipeline integrity in the area impacted by a landslide.
Ground movement by landslides oblique to the orientation of the pipeline can cause lateral deflection as well as localized axial elongations/contractions in the pipeline, which will result in accumulation of bending and axial strains on the pipeline. Common factors impacting the magnitude of strain accumulation are pipeline deflection (or out-of-straightness), deflected pipeline length (engaged part of the pipeline within the body of the landslide), pipeline diameter, and orientation of the pipeline relative to the direction of landslide movement.
This paper will review and present the above information for more than 70 landslide sites within the Appalachian region of the USA. This paper will also present a correlation between the measured bending strain from the IMU tool runs and the pertinent pipeline features such as pipeline out-of-straightness, deflected length, pipeline diameter, and pipeline orientation relative to the landslide direction.
This paper is intended to assist pipeline geohazard practitioners in performing the first round of induced bending strain screening under conditions where IMU bending strain data may not be available.
Michiel Brongers
Kiefner and Associates, Inc., Columbus, USA
Operators with existing pipelines with laminations may have the desire to perform welding to install fittings or other appurtenances. This paper presents the results of an evaluation of the potential threat of lamellar tearing under in-service fillet welds. The research included modeling to determine the minimum recommended distance for welding at or near laminations, and a full-scale hydrostatic pressure-hold test on laminated pipe with welded fittings to demonstrate if the presence of laminations would interfere with the welds. Four different scenarios were investigated: (1) fitting welded over laminated area, (2) portion of weld bead place on top of a localized lamination, (3) weld bead some distance from localized lamination, and (4) fitting welded on non-laminated area of pipe with laminations elsewhere. The developed approach was a unique and innovative way to evaluate welding on pipe with laminations. The results from this project and the provided guidance that was developed will benefit the pipeline industry as a whole.
Intisar Rizwan i Haque, Ryan Lacy, Simon Bellemare
Massachusetts Materials Technologies, Natick, USA
Growing use of advanced In-line Inspection (ILI) for detecting seam anomalies has increased the demand for Engineering Critical Assessment (ECA) to differentiate the many non-severe features that do not need repair from features in certain assets where repairs are warranted. To perform the ECAs and reduce the number of unnecessary excavations of vintage lines, pipe cutting for laboratory testing has become more common to obtain Charpy V Notch (CVN) toughness, which is often unavailable when legacy manufacturing standards did not require such testing. Non-destructive evaluation (NDE) of pipe seam toughness as a part of opportunistic data collection is an attractive alternative to pipe cutouts and can be applied to prior excavations with sufficient NDE data. An NDE process using the frictional sliding method and other surface measurements has been recently validated for assessing the seam toughness of vintage electric resistance welded (ERW) pipes. This paper details this NDE process and its validation, along with results from case studies of its initial field deployment. The field instrumentation is the same as used for pipe grade determination using the frictional sliding method. When certain conditions are met for a given ERW pipe population, a ductile fracture initiation and an associated CVN toughness of 10 ft-lbs can be positively confirmed when conservatively accounting for measurement uncertainty. Utilizing a toughness of 10 ft-lbs is a significant advantage over conservative values such as 4 ft-lbs for gas transmission pipelines with no history of failure. Field deployment of this process has successfully reduced the total number of excavations on projects. The NDE process capabilities can be further enhanced when combined with an NDE determination of pipe body toughness, using a separate, but complementary, technique.
Matt Ellinger, William Harper, Pam Moreno, Stacy Hickey, Adriana Nenciu, Preston Galloway
DNV, Dublin, USA
Results from magnetic flux leakage (MFL) in-line inspection (ILI) surveys provide valuable information that help pipeline operators make informed and defensible integrity management decisions. When subsequent ILI survey data are available, meaningful, and data-driven corrosion growth rates can be derived along the length of a pipeline by performing a comprehensive ILI-run-to-run comparison. A comprehensive ILI run-to-run comparison should include the following components:
ILI vendors typically identify metal loss anomalies that are on (i.e., crossing) the longitudinal seam weld or near (i.e., adjacent to, or in the heat affected zone) of the longitudinal seam weld versus those that are in the pipe body (i.e., away from the longitudinal seam weld). During a comprehensive ILI run-to-run comparison analysis, the authors of this paper observed a trend in which ‘spreadsheet-based’ corrosion growth rates for metal loss anomalies reported on or near the longitudinal seam weld were consistently higher than those reported in the pipe body. Following this observation, the authors performed an in-depth analysis to better understand this trend. The following tasks were completed as a part of the analysis:
This paper will detail the methodology and results of the authors’ analysis. Key findings and practical applications will be presented. The paper will provide valuable insights into managing pipeline integrity with respect to ILI-reported metal loss anomalies at or near the longitudinal seam weld.
Tom Bubenik, Steven Polasik, Benjamin Hanna
DNV, Dublin, USA
Effective area calculations are used to identify which corrosion depth measurements control the failure pressure of a cluster of metal-loss anomalies reported by an in-line inspection (ILI). The depth measurements usually correspond to individual anomalies that are grouped together based on defect interaction criteria. The effective area calculations determine an effective length and depth based on the ILI reported cluster and box lengths and depths at the time of the inspection. As corrosion growth occurs, though, the depths of some or all of the individual anomalies within a cluster can increase. As a result, the effective length of the cluster can increase or decrease.
Growth of individual anomalies within a cluster is often non-uniform, with some anomalies increasing in depth (and possibly length) more quickly than others. As a result, local “hot spots” can develop and eventually dominate the effective area calculations. Understanding how corrosion growth affects the effective dimensions of a cluster is important in estimating remaining lives and determining which clusters are most likely to fail first. The flaw geometry at failure depends on the local operating pressure, the corrosion growth rates, and the initial cluster geometry.
Remaining life calculations depend on reliable estimates of both initial and final metal loss depths and lengths. Because differences between individual metal loss box corrosion growth rates can affect effective flaw dimensions, accuracy is important. Initial corrosion depths and lengths are reasonably well known from typical ILIs. Overestimating or underestimating the flaw geometry at failure under operating conditions can lead to overly conservative or unconservative remaining life predictions.
This paper evaluates the effects of corrosion growth on the effective dimensions, flaw geometries at failure, and remaining lives of clusters. The authors examine 20 real-world clusters ranging in length from short to long and containing few to many individual anomalies. The authors determine when and how each cluster’s effective length and critical depth changes as corrosion growth takes place along the cluster until it reaches a failure condition at the local operating pressure. Then, they evaluate how the changes in effective lengths and critical depths affect remaining life predictions. Conclusions regarding how to best estimate remaining lives of clustered anomalies are developed and documented.
KEYWORDS: Engineering analysis, ILI analysis, ILI applications, Corrosion studies
Greg Zinter1, James Staszuk1, Cory Solyom2, Brianna Bossio3
1PureHM, Edmonton, Canada. 2PureHM, Calgary, Canada. 3Enbridge Inc., Edmonton, Canada
Inline inspections tools and cleaning pigs are routinely used to ensure the safe and economical operation of oil and gas pipelines. While in the pipeline, all ILI tools and pigs must be tracked on a real time basis so that the pipeline can be operated safely. Recent developments in remote ILI tool tracking technology have improved the safety of ILI projects by eliminating the need for field technicians to travel to site to witness the tool passage. These improvements have also made tool tracking more reliable and, most often, lower cost.
Remote tracking offers operators a way to track their inline inspection tools without the need to constantly have field personnel actively on the ROW, effectively reducing risks to personnel and the project. This is of particular increased benefit when tracking overnight and over difficult to access terrain. Traditionally, the solution for difficult access has required the aid of helicopters for AGM deployments, and retrievals, meaning significant effort is required to facilitate tracking for every single project. As pipeline owners look to enhance their inspection programs through increased inspection frequency, these issues of accessibility are exacerbated. Advancements in tracking technology and services are addressing this issue and making it easier and cheaper to track their critical ILI tools.
For example, Enbridge has installed a permanent remote tracking system across large inaccessible sections of its Athabasca pipeline network. This system consists of a series of AGMs, strategically located to ensure full tracking coverage. These remote systems are permanently installed and powered by solar energy. Pure HM has partnered with the Enbridge to monitor this system 24/7, year-round to ensure consistent and reliable tracking of any tool used in the line, eliminating the need to mobilize field technicians or helicopters.
This paper will explore the innovative approach Enbridge has taken to mitigate risk and drive a cost saving of over $4,000,000 over the duration of the 5-year program.
Xiang Peng1, Kevin Siggers1, Johannes Palmer2, Gurwinder Nagra3
1ROSEN Technology Canada Ltd., Kelowna, Canada. 2ROSEN Technology and Research Center GmbH, Lingen, Germany. 3Enbridge Liquids Pipeline, Calgary, Canada
The inspection capability of magnetic flux leakage (MFL) is subject to the angle between its magnetic field and the defect. To get a comprehensive assessment on corrosion defects, more and more pipelines are inspected with two MFL techniques with perpendicular magnetic fields, i.e., axial MFL (MFL-A) and circumferential MFL (MFL-C). Currently, inspection data from each MFL tool are analyzed separately, and two inspection reports are generated respectively. In this paper, we propose a model which aligns the data from two magnetic field orientations and fuses the respective signals into a single inspection result to achieve a 3D metal loss profile with laser-like precision. The alignment of the signals is achieved through conversion into the same modality i.e., MFL-A converted to MFL-C and vice versa. The fusion model is a neural network trained on historical MFL and laser scan data. It takes the aligned MFL-A and MFL-C signal data as the input and produces 3D metal loss profiles with high resolution. In this case study with Enbridge Liquid Pipelines, the proposed model is validated on the field data from an operational pipeline. The depth comparison of the derived 3D metal loss profiles versus laser scan profiles has very promising results. The 3D metal loss profiles are also used as inputs to RSTRENG as well as P² methodologies. The detail of the fusion derived profiles, compared to the box derived profiles, leads to a more accurate estimation of pipeline burst pressure.
Shanshan Wu1, Joseph Bratton1, Jing Wang2, David Kemp1, Luyao Xu1, Greg Quickel1
1DNV, Dublin, USA. 2TC Energy, Calgary, Canada
The Pipeline and Hazardous Materials Safety Administration (PHMSA) issued RIN2 of the Final Rule (frequently referred to as the “Mega Rule”) on August 4, 2022, which will impact the pipeline industry’s approach to the assessment of dents and other mechanical damage. The Mega Rule provides detailed requirements in the Code of Federal Regulations (CFR) Title 49 Part §192.712(c) regarding how to perform a dent engineering critical assessment (ECA). With the Mega Rule taking effect in 2024, it is expected that more dents will be considered for ECA to determine the response plan and timeline.
This paper will share guidance on selection criteria for dent ECA through five case studies. The case studies include Ductile Failure Damage Indicator (DFDI), Strain Limit Damage (SLD), and dent fatigue analysis using finite element analysis (FEA). Additionally, findings from field investigations, laboratory results, and other pertinent information associated with the respective dents will be presented. Guidance regarding best practices to assist operators in selecting suitable locations for dent ECA versus excavation will be provided from the case studies.
The primary objective of this paper is to share experiences to the industry ahead of the upcoming dent ECA requirements outlined in Part §192.712 (c). This paper will share lessons learned for things to consider when evaluating the suitability of performing an ECA and to help avoid sole reliance on ECA results when other factors demonstrate that the results may not be reliable.
Mark Wright, Amin Singh, Tanner Jones
ROSEN USA, Houston, USA
Achieving zero incidents has been a key safety objective across the pipeline industry. The relationship between the pipeline industry and pipeline regulations has seen several iterations since the first regulations were introduced in 1968. Significant changes and rigorous regulations enacted in 2002 required pipeline operators to create a structured framework for risk and integrity management programs. However, subsequent safety performance has been static, as detailed in the preamble to more recent updates in 2019. Pipeline regulations serve as minimum requirements for achieving operational safety by reducing incidents, and there should be hope of a more substantial impact with the effects of rule changes to both gas and hazardous liquid pipeline regulations in 2019.
Failures of pipelines are often complex, involving primary, secondary and even tertiary contributory factors, while rulemaking must be discrete and realistically achievable for compliance. Thus, failures and rulemaking are not completely associative, but neither are they mutually exclusive. The preamble to the 2019 rules identified clear lineages between a subset of significant events and rulemaking i.e. measures that directly address some of the causes of significant events. Whilst this seems intuitively sensible, where do these solutions lie in the spectrum between causality and mutual exclusivity on a wider scale?
All pipeline failures are undesirable, but each provides an opportunity to learn and highlights systemic vulnerabilities by identifying areas for improvement. This paper explores reported failure data for both gas and liquid transmission pipelines in the U.S. between 2003 and 2022. The paper will identify trends and thus residual gaps in understanding of failures within the industry for proactive measures to prevent future incidents. The complexity of failure will be explored by review of supplementary NTSB investigation reports and commentary on the combination of factors at play. The primary goal of integrity management is to operate assets such as pipelines safely. Inherent is that integrity management cannot be about doing everything possible, rather maximizing everything practicable. This paper hopes to identify what practicable may look like now and in the future.
David Kemp1, Shanshan Wu1, Joseph Bratton1, Luyao Xu2
1DNV, Dublin, USA. 2DNV, Calgary, Canada
With PHMSA’s issuance of RIN2 of the Final Rule, Engineering Critical Assessments (ECA) have become increasingly important in assessing not only the fatigue life of dents and other integrity threats, but also reinspection intervals. ECA’s can be performed for a variety of complex dent features identified from in-line inspection (ILI) or direct examination by following assessment methodologies prescribed in API 1183 along with the fatigue life assessment procedures outlined in API 579.
For those cases requiring a level 3 assessment, finite element analysis (FEA) is often necessary to account for interactions between dents and additional features (i.e., metal loss, bending strain, seam welds, etc.), which can then be used to determine the fatigue life of the dent. A more accurate fatigue life can be calculated using the FEA results to obtain a stress vs. pressure relationship, which is then paired with the pressure history of the specific line segment being assessed. This stress vs. pressure relationship is extracted from a specific location in the vicinity of the dent from the finite element model, and for the sake of conservatism in the assessment, is either taken from the location of maximum stress or the location of maximum change in stress between pressure cycles. Both stress locations are critical to dent integrity, the former is usually associated with crack generation during the dent formation process, while the latter contributes to the fatigue crack initiation and growth. Depending on the dent conditions (i.e., constrained, unconstrained, dent depth, shape, feature interactions, etc.) these two locations are not always coincident and the resulting fatigue stress range could be significantly different in some scenarios.
For this paper, a collection of over 30 dent ECAs are examined to determine under what conditions, such as constraint condition, shape, stress/strain level, etc., the locations of maximum stress and maximum change in stress are not coincident as well as the extent to which these differences impact the overall fatigue life of the dent features.
Gemma Simpson1, Nancy Thomson1, Courtney West1, Jane Haswell2, Andrew Cosham3, Gary Senior2
1SGN, Edinburgh, UK. 2PIE, Newcastle, UK. 3ninthplanet, Newcastle, UK
The Local Transmission System (LTS) is the backbone of the UK (UK) energy network, delivering natural gas from the National Transmission System (NTS) to towns and cities across the country.
The four Gas Distribution Networks (GDNs) operate approximately 11,000 km of high-pressure pipelines, operating at pressures above 7barg. The pipelines were originally designed to transport and store natural gas.
The UK Hydrogen Strategy states that: “Low carbon hydrogen will be critical for meeting the UK’s legally binding commitment to achieve net zero by 2050”. Hydrogen behaves differently to natural gas, therefore it is necessary to assess how it affects the existing LTS infrastructure.
The LTS Futures Project is a first-of-a-kind, £30 million, joint funded project between SGN, the UK energy market regulator OFGEM, and the other UK GDNs. The project is led by SGN and looks to repurpose a 30 km natural gas transmission pipeline to hydrogen for a live demonstration trial, which will inform the development of a Blueprint methodology for repurposing the LTS. The LTS Futures Project is researching, testing and collating evidence to understand the compatibility of LTS assets, pipelines, associated plant and ancillary fittings in hydrogen which will be captured in the Blueprint.
The aim of the Blueprint is to provide a methodology to determine if a natural gas LTS asset is fit for hydrogen service and identify any data gaps, or further work needed for repurposing for hydrogen service.
This paper provides details on the technical approach adopted by the project, the progress to date and the plan going forward.
Keywords: Repurposing. Hydrogen.
Tristan MacLeod
Kiefner and Associates, Inc., Ames, USA
Cyclic fatigue of crack-like anomalies is a well-known threat to pipeline integrity. Manufacturing defects in the longitudinal seam (especially in pipe manufactured prior to 1970) as well as stress corrosion cracks in the pipe body may enlarge and fail in service due to pressure-cycle-induced fatigue. In fact, the current U.S. pipeline integrity management regulations require crack growth and remaining life assessments for natural gas pipelines in high consequence areas and segments known to be susceptible to cyclic fatigue.
To manage the risk of failure from pressure-cycle-induced fatigue, pipeline operators should employ integrity assessments either via hydrostatic testing or in-line inspection using a reliable crack-detection tool. The appropriate period for reassessment depends on the sizes and growth rates of potential defects that may still exist after an initial hydrostatic test or in-line inspection. The pressure-cycles applied to the pipeline may cause the just-surviving defects to grow at a rate inherent to the material and its environment. Long-established principles can be used to predict remaining life. Pipeline operators can use these methods to plan timely reassessments to prevent failures.
This paper describes one approach to predicting reassessment intervals. This approach has evolved over a period of more than 30 years. Careful analysis of all of the known data can avoid pitfalls and inappropriate remaining life predictions. The purpose of the paper is to show that while the well-known and widely available basic principles are sound, their application to pipeline integrity management requires an in-depth understanding of the particular pipeline being assessed.
Lucinda Smart, Benjamin Wright, Dyke Hicks
Kiefner and Associates, Inc, Ames, USA
Within the last few years, there have been increasingly more vendors and operators looking into ways to improve the accuracy of ILI data correlations with both in-ditch validation methods as well as across consecutive ILI runs. It may seem obvious, but it is important to ensure the defects that are being correlated from one data source to the other are, in fact, the same defect. ILI data correlations can be particularly difficult when differing vendors or tool technologies are applied, or if location conventions are not applied similarly from one run to the next. If there are inaccuracies in the locations and orientations provided by the vendor, or if the dig site location is not verified and reference locations are not correct, this leads to meaningless data results. This paper will go into detail in the discussion for guidance of ILI data correlation from both successive ILI assessments for growth rate assessments, as well as in-ditch NDE data to ILI data for tool validation practices. The primary method discussed will be a pattern-matching approach, where sources of error can be reduced by aligning overall patterns of reported defects using modern software tools along with insight from experienced analysts. Applying expertise in this manner leads to more accurate outcomes for tool validation, corrosion growth rate (CGR) assessments, and probability of identification or detection (POI or POD), which then ultimately lead to better and more informed integrity management decisions.
Christopher De Leon1, Rachel Brossman2
1D2 Integrity LLC, Houston, USA. 2PBF Energy, Cerritos, USA
In-line inspection (ILI) continues to evolve and prove to be a high-value solution for performing pipeline integrity assessments. Industry has seen ILI promoted through NTSB recommendations, Federal Pipelines Safety Statutes by Congress, and PHMSA’s recent updated pipeline federal regulation. However, each ILI technology and its application by ILI service providers must be vetted by pipeline operators to ensure it is qualified for the inspection goals and objectives. Unfortunately, some ILI technology is not properly vetted commensurate to the risk associated with the integrity assessment for a given pipeline. As governance, PHMSA has now incorporated by reference API STD 1163 In-line Inspection Systems Qualification (API 1163) into both 49 CFR 192 and 195. While API 1163 is generally understood, details can be overlooked, leading to non-compliance. This paper uses two case studies to highlight the topic of ILI System Selection within the API 1163 standard and its importance in performing a sound integrity assessment. The process used for selecting an appropriate ILI system for corrosion and cracking threats will be reviewed, and how compliance with new regulations was specifically considered.
Topics: Regulation and Compliance, Codes and Standards, ILI Applications, ILI Analysis
Christopher Davies1, Cameron Cooper1, Lee Sellers2
1ROSEN USA, Houston, USA. 2ENERGY TRANSFER, Houston, USA
In response to the discovery of Selective Seam Weld Corrosion (SSWC) on a 12-inch natural gas pipeline, an in-line inspection (ILI) was completed using an ultra-resolution circumferential magnetic flux leakage tool. The closer sensor configuration of this system allowed for a more detailed recording of the magnetic leakage profile and ensures that the peak value of flux leakage is recorded within complicated corrosion morphologies such as SSWC.
Through an optimized evaluation process, all corrosion anomalies considered to be associated with the longitudinal weld were subject to detailed review. The review provides a thorough understanding of the different signal characteristics and likelihood classifications of ‘likely’, ‘possible’ and ‘unlikely’ SSWC are assigned. The initial evaluation process resulted in the identification of 23 ‘Likely’ SSWC anomalies and 35 ‘Possible’ SSWC anomalies. All remaining corrosion anomalies associated with the longitudinal weld were classified as ‘Unlikely’ SSWC. Classification is critical as it pertains to integrity management. Understanding the pipeline’s susceptibility to SSWC, the detection capability of the ILI system and the confidence of likelihood classifications allows for process driven discrimination between SSWC and ‘general corrosion’ in the area of the longitudinal weld.
Validation of the evaluation and classification was achieved through a structured dig program. A total of 3 excavations were performed on the pipeline, which targeted a total of 24 anomalies associated with the longitudinal weld. Evidence of SSWC was observed for 11 of the 13 ‘Likely’ SSWC classifications. Of the five (5) ‘Possible’ SSWC calls investigated, three (3) were confirmed to be SSWC. No evidence of SSWC was observed for the ‘Unlikely’ SSWC classification subject to infield investigation. The results of these excavations were used to reclassify all remaining anomalies associated with the longitudinal weld.
A critical aspect of the likelihood classification process is iteratively incorporating information from field investigations. This paper presents the close collaborative efforts performed by a pipeline company and an ILI service provider, to help manage the threat of SSWC on a 12-inch pipeline. It is intended to present an ILI based approach to assess SSWC and share recent experience with the industry on a targeted approach in managing the threat of SSWC.
Santiago Urrea1, Jordi Aymerich2, Sayan Pipatpan1, Tannia Haro3, Alex Hensley3, Christopher Newton4
1NDT Global, Stutensee, Germany. 2NDT Global, Barcelona, Spain. 3NDT Global, Houston, USA. 4Phillips 66, Houston, USA
Pipeline operators employ various strategies to ensure the operational safety of their pipeline systems. A crucial element of this strategy involves In-line inspection (ILI) and Non-destructive examination (NDE). However, what happens when all available evidence points to a systematic limitation in the performance specification of these systems? How can the operator utilize this data within their Integrity Management Program (IMP)? Lastly, can this data be effectively utilized to derive new rules and analysis processes?
NDT Global, in collaboration with an operator, has been tasked with investigating, documenting, and delivering a novel approach to identifying crack complexity, specifically hook cracks, within a population of previously detected and undersized features. Currently, there is no ILI tool available in the specific required diameter and wall thickness range in the market that meets the requirements or performance specifications necessary to provide essential information for engineering assessments and the proper ranking of such features.
The primary objective of the research and validation is to develop an approach that provides a systematic method for identification and, potentially, a correction factor for depth sizing. These critical attributes can then be effectively used for engineering calculations, priority ranking and risk mitigation activities.
This innovative approach incorporates years of accumulated knowledge from other pipelines to develop a systematic analysis approach. Additionally, it involves the calibration of this approach through collaboration with the operator, utilizing advanced and non-conventional in-ditch NDE techniques to determine accuracy, and potentially employing destructive testing during lab testing.
This paper is a summary of the research and collaboration between NDT Global’s international experts and a USA pipeline operator.
Ron Thompson1, Xavier Ortiz2, Richard Kania3, Andrew Corbett1, Guillermo Solano1
1Novitech Inc., Toronto, Canada. 2Plains Midstream Canada, Calgary, Canada. 3KanEnergy Partners Inc., Calgary, Canada
In the late 1990’s, the discovery of stress corrosion cracking (SCC) in orientations other than the axis of the pipe triggered new studies into the factors associated with off-axial cracking. Since most of the crack colonies appeared to be close to 90 degrees to the axis of the pipe, the investigations focused on circumferentially oriented SCC (CSCC). Notwithstanding, there have been many documented cases of cracks at angles other than 90 degrees, notably at the same angle of the spirally applied tape in tape-coated pipelines. These off-axis cracks have been incorporated into the models developed to address CSCC.
CSCC management programs use of a combination of quantitative and qualitative data involving bend strain along with susceptibility criteria, geohazards and areas of pipe movement, and ILI where available. As CSCC investigative and remedial work continues, off-axis cracking is starting to be found in larger numbers, with skew angles to the axis of the pipe ranging from 45 to 90 degrees. These skew angles can exceed the specified detection range of ILI tools, leaving operators without a diagnostic option for modelling these types of features.
This study illustrates the successful management of both circumferential and off-axis SCC by using a magnetic based ILI system to determine crack depth, crack length and the primary crack colony skew angle. The determination of all these crack attributes, particularly the skew angle, enabled modelling the interaction between axial and hoop stresses, to calculate the pipeline’s remaining strength.
The diagnostic data for the program was obtained using ILI technology that included three sensor systems: AMFL, CMFL, and IDD-SM™. This technology reliably provided crack length and depth sizing with an accuracy of +/- 15% and, for this study, the measurements of the primary colony skew angle with a target accuracy +/- 10°.
The ILI’s crack sizing and crack skew angle measurements were corroborated through an extensive excavation campaign, which also established ILI detection (POD) and identification (POI) greater than 95%, this accuracy supported the use of crack model predictions that could be incorporated into reliability programs.
The ILI reported and verified CSCC locations also supported the management of geohazards as it was possible to identify potential ground movement locations that were not highlighted by geotechnical desktop and field investigations.
The lines used in this study had a nominal diameter of 8.625” and were investigated for occurrences of all threat types including off-axis and circumferential cracking. Field inspection data was gathered to support the finding of this study and the implementation of the model.
Chris Alexander, Chantz Denowh
ADV Integrity, Inc., Manolia, USA
One of the greatest challenges facing today’s pipeline integrity engineers is determining the threat level a given feature or defect poses to a pipeline system. The process employed by most pipeline integrity engineers starts with inspection measurements made with in-line inspection tools or in-the-ditch inspection technologies. If the measured data are deemed a threat to pipeline integrity, an assessment is conducted using either closed-form engineering equations or numerical modeling techniques such as finite element analysis. To supplement assessment efforts, a well-designed and conducted full-scale testing program can provide valuable insights about the true performance characteristics of a defect and improve the accuracy of failure prediction methods.
This paper includes examples of how full-scale testing can be used to provide a more accurate and complete picture of defect performance under various loading conditions including burst, cyclic pressure, tension, and bending. Included is a brief description of the types of tests that can be conducted, accompanied with photos from actual tests. Information is also included on the types of equipment and measurement devices that are used in full-scale testing. The goal of this paper is to demonstrate the inherent benefits in employing full-scale testing as a means for better understanding and predicting the threat levels associated with certain defects.
Chantz Denowh1, Robert Stakenborghs2, Liang Yu3
1ADV Integrity, Inc., Houston, USA. 2Advanced Microwave Imaging, Baton Rouge, USA. 3Baker Hughes Flexible Pipe Systems, Houston, USA
The use of spoolable composite pipe technologies in the onshore oil and gas industry has expanded significantly over the past decade. It is anticipated that interest will only continue to grow as oil and gas operators transition to transporting alternative fuels such as hydrogen and carbon dioxide. Currently, these technologies have been limited to non-regulated lines such as gathering lines or produced water transport, but the need is growing to expand into the high-pressure transmission pipelines. These lines will typically be in the 4-inch to 8-inch size range and rated up to 3,000 psig. There are several gaps in knowledge to address though before making this step. One gap is the need for viable inspection technologies that pipeline operators can for long-term integrity management.
This study works to address this gap by progressing the multifrequency microwave technology and evaluating its accuracy against simulated defects that commonly occur to spoolable composite pipes in the field. The phases of the study described in this paper include an initial calibration of the microwave technology to the pipe design, material types, and layer depths. Following calibration, an open inspection was completed on pipes with known defect location, size, and depth. This information was shared with the microwave vendor to improve sizing and location accuracy of equipment and software. Additional pipes with similar defects were then used for a closed inspection to evaluate the technology’s ability to accurately locate and size unknown defects. The pipe used in this study was nominal 4-inch with a nominal pressure rating of 1,500 psig.
The last phase of the study included inspection of pipe samples with simulated damage that commonly occurs in the field. Examples of recreated damage include pipe ovalization, overbending (kinking), and over-tensioning. This damage was recreated in a laboratory setting. The damaged pipes were subjected to destructive testing following the inspection (test results not included in this paper). Results and findings from each of the above phases are described in this paper including an evaluation of the location and sizing accuracy. Inspection of the simulated damage is discussed and compared to results of the destructive testing where damage indicated the presence of damage in the pipe reinforcement.
Michael Rosenfeld1, Richard Gailing2, Benjamin Zand1, Joel Anderson3
1RSI Pipeline Solutions LLC, New Albany, OH, USA. 2Retired, Sandy, OR, USA. 3RSI Pipeline Solutions LLC, Oklahoma City, OK, USA
To reconcile differing requirements for pipeline cover in various standards and regulations, an evaluation was performed of the effect of cover depth and consistency on susceptibility to damage, other threats, risk, cost-benefit, and construction, with some surprising results. Current and historical US and foreign gas and liquids standards and regulations were compared. US and international incident data were analyzed to determine the relationship between cover depth and mileage-normalized risk of damage, and risk of other integrity threats such as geohazards and corrosion. FEA was performed to understand how cover depth and trench design affects susceptibility to rock damage. A cost-benefit analysis of increased depth of cover was performed. Sensitivity of transported product (gas vs liquid) to the benefit of cover were determined. Recommendations were made for improved codes content.
Rick Sugden
Kiefner and Associates, Denver, USA
Modern hydrostatic testing is often seen as a “check the box” for new construction. It is required by code for most pipelines. In the fast-paced culture of “get ‘er done” world, is pipeline hydrotesting still needed? With so many technological advances, can we just remove this requirement? In the mind of the inspector, are discrepancies: “just temperature”, “not regulated”, “don’t matter?” This presentation is designed for the inspector that is signing off their name on a hydrostatic test. Do you believe that this pipeline is safe, that it is not leaking? I will discuss what is obvious, what is not so obvious and why You as inspector or engineer should verify all the data. By the way, what are you signing for? What should you be concerned about? How will the new regulations impact the future of hydrotesting?
Mick Collins
Intero Integrity Services, Houston, USA
Traditionally, Gulf of Mexico (GoM) Outer Continental Shelf (OCS) owners and operators have sought alternate methods to assess the integrity of their gathering lines than inline inspection. In April 2010, the Deepwater Horizon explosion, and subsequent blowout, brought significant scrutiny from both state and federal regulatory agencies.
A customer approached Intero Integrity Services in 2019, in order to evaluate feasibility of inline inspections of its liquid gathering system in the GoM. The feasibility included three areas: 1) Technical ability to inspect; 2) Cost of inspection; and 3) Value of reported results.
From a technical standpoint, the customer conditions challenged just about every aspect of standard inline inspections: Never pigged for maintenance nor integrity assessment; 1500 psi static pressure; limited operating space on platform; remote location (90+ miles offshore); inability to track during the inspection (2,000’ water depth); limited pipeline availability based on production schedule; 8” nominal x 0.812 wall thickness x 25 mile pipeline; back to back “jumpers” to loop pipeline; and pumped in sea water. This paper will explain how, working closely with the operator, flow conditions were tightly controlled.
From a cost perspective, the customer had limited assessment options. The field was initially developed in 1998 and has operated in multi-phase production for 20+ years. If pipeline replacement is required, the field will just shut-in based on ROI compared to the current production curve. External assessment methods are limited (ROVs and divers) and need to be more comprehensive. Other than inline inspection, a hydrotest was the only option. Again, not valuable information for the cost.
Corrosion was detected in an area that had limited access; therefore, the operator decided that an annual inspection would be conducted and detailed corrosion growth assessments completed, and also to quantify the effectiveness of corrosion mitigation methods. Data sets will be presented that show the challenges of detecting defects under external clamps, and the variability between said datasets.
With the 0.812” wall thickness, the only inline inspection solution was ultrasonic (UT) technology. Magnetic (MFL) tools would not be able to saturate the pipe wall to provide accurate measurements.